hbot homes correctly but prints mirrored ,

[tracar]

@peter247 yes z0 is Zero

after it homes to z0 it backs off 5mm

[peter247]

@tracar

So what is next to do bed.g / G32 ?

[tracar]

next is to get it to recognize it has a bltouch attached, as M280 P7 S10 :deploy bltouch does not work

[Phaedrux]

@tracar said in hbot homes correctly but prints mirrored ,:

M280 P7 S10

If we're using RRF3 now, that should be P0 instead of P7.

There should be an M950 command in your config.g that create the servo 0 pin for the bltouch. That's where the zero comes from.

[Phaedrux]

Doing up a diagram like this can be very helpful in getting the offsets all straight. Piece of grid paper works well if you're not a paint wiz.

There's also some useful info here:
https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe
https://duet3d.dozuki.com/Wiki/Using_mesh_bed_compensation
https://duet3d.dozuki.com/Wiki/Bed_levelling_using_multiple_independent_Z_motors

This page will also be useful for getting the hang of RRF3:
https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview

And of course the Gcode wiki that will tell you how each gcode works:
https://duet3d.dozuki.com/Wiki/Gcode#main

[peter247]

@tracar

Which heater pin are you using ?.

Mine is heater 7 , so this should help you .

; Z-Probe config.g
 
M558 P9 C"^zprobe.in" H2 F100 T8000 A5		; set Z probe type to bltouch and the dive height + speeds
M950 S0 C"exp.heater7"							; create servo pin 0 for BLTouch
G31 P500 X-45 Y-6 Z2.98                        	; set Z probe trigger value, offset and trigger height
M557 X55:295 Y55:295 S80                     	; define mesh grid .. 30 , 60 , 80

Lines 5 and 6 set to your own offsets and mesh grid
This works with any heater

; deployprobe.g
; called to deploy a physical Z probe
;
M280 P0 S10 ; deploy BLTouch

; retractprobe.g
; called to retract a physical Z probe
;
M280 P0 S90 ; retract BLTouch

[tracar]

yes H7_pwm on the end of the expansion board

can not get a response from the bltouch

; Self-Test
;
M280 P0 S120 ; Send PWM channel 7 the S10 (angle) command, inverted signal

[Phaedrux]

@tracar said in hbot homes correctly but prints mirrored ,:

can not get a response from the bltouch

And that's using this in your config,g?

M558 P9 C"^zprobe.in" H2 F100 T8000 A5 ; set Z probe type to bltouch and the dive height + speeds
M950 S0 C"exp.heater7" ; create servo pin 0 for BLTouch

If that's what you have in config, and it's wired to the right pin, check the wiring continuity.

[tracar]

this is the current config

; Z-Probe

M950 S0 C"exp.heater7" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T24000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y0 Z0.445 ; set Z probe trigger value, offset and trigger height
M557 X50:400 Y50:500 S50 ; define mesh grid

and

; deployprobe.g
; called to deploy a physical Z probe
M280 P7 S10 ; deploy BLTouch
does not work

continuity of wiring is fine

[peter247]

@tracar

BIG HINT ,This works with any heater

; deployprobe.g
; called to deploy a physical Z probe
;
M280 P0 S10 ; deploy BLTouch

; retractprobe.g
; called to retract a physical Z probe
;
M280 P0 S90 ; retract BLTouch

[tracar]

i have already changed the p0 and still non responsive

[peter247]

@tracar , what pin are you using .

[tracar]

@tracar said in hbot homes correctly but prints mirrored ,:

H7_pwm on the expansion board
and zprobe in

[peter247]

@tracar Pin 31 ?

[tracar]

@peter247 yes

[peter247]

This post is deleted!

[peter247]

This post is deleted!

[peter247]

@tracar

I can't see anything wrong with the set ups .

if you had a Maestro that needs to be set up differently , but you are running a duet 2 wifi , so that doesn't wash .

Can only think it's wiring ?

[tracar]

it works if i downgrade firmware

[peter247]

@tracar

what is your full zprobe config

have you removed the M307 H7 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch