• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

hbot homes correctly but prints mirrored ,

Scheduled Pinned Locked Moved
Tuning and tweaking
4
169
8.7k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    peter247 @tracar
    last edited by peter247 25 Aug 2020, 21:25

    @tracar

    comment out M307 H7 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch

    Notes - RepRapFirmware 3

    The F parameter is no longer supported. Use M950 to set the frequency in the M950 command that you use to define the heater .

    The I2 parameter is no longer supported, and I3 does the same as I1. You can use M950 to invert the output.

    You can no longer disable a heater using M307 A-1 C-1 D-1. To use the pin for something else, don't create a heater on that pin.

    1 Reply Last reply Reply Quote 0
    • undefined
      tracar
      last edited by 25 Aug 2020, 21:36

      wiring is all good, as i said it works if i downgrade the firmware,
      something in the settings..............

      undefined 1 Reply Last reply 25 Aug 2020, 21:40 Reply Quote 0
      • undefined
        Phaedrux Moderator
        last edited by 25 Aug 2020, 21:37

        Can you put up your full config.g?

        Z-Bot CoreXY Build | Thingiverse Profile

        undefined undefined 2 Replies Last reply 25 Aug 2020, 21:39 Reply Quote 0
        • undefined
          peter247 @Phaedrux
          last edited by peter247 25 Aug 2020, 21:39

          This post is deleted!
          1 Reply Last reply Reply Quote 0
          • undefined
            peter247 @tracar
            last edited by 25 Aug 2020, 21:40

            @tracar

            have you commented out M307 H7 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch

            undefined 1 Reply Last reply 25 Aug 2020, 21:56 Reply Quote 0
            • undefined
              Phaedrux Moderator @peter247
              last edited by 25 Aug 2020, 21:56

              @peter247 said in hbot homes correctly but prints mirrored ,:

              M307 H7 A-1 C-1 D-1

              Will just be ignored in RRF3.

              If you send M98 P"config.g" do you get any errors echoed back?

              Z-Bot CoreXY Build | Thingiverse Profile

              undefined 1 Reply Last reply 25 Aug 2020, 22:01 Reply Quote 0
              • undefined
                tracar @Phaedrux
                last edited by 25 Aug 2020, 22:00

                @Phaedrux
                ; Configuration file for Duet WiFi (firmware version 3)
                ; executed by the firmware on start-up
                ;
                ; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Aug 25 2020 08:01:23 GMT-0600 (Mountain Daylight Time)

                ; General preferences
                G31 X0 Y0 Z0 P25
                G90 ; send absolute coordinates...
                M83 ; ...but relative extruder moves
                M550 P"Duet2" ; set printer name
                M669 K1 ; select CoreXY mode

                ; Network
                M552 S1 ; enable network
                M586 P0 S1 ; enable HTTP
                M586 P1 S0 ; disable FTP
                M586 P2 S0 ; disable Telnet

                ; Drives
                M569 P5 S0 T5 R1 ; physical drive y goes forwards
                M569 P6 S1 T5 R1 ; physical drive x goes forwards
                M569 P7 S1 T5 R1 ; physical drive z goes forwards
                M569 P8 S1 T5 R1 ; physical drive z2 goes forwards
                M569 P3 S1 ; physical drive extruder goes forwards
                M584 X6 Y5 Z7:8 E3 ; set drive mapping
                M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                M92 X200.00 Y200.00 Z200.00 E138.23 ; set steps per mm
                M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                M203 X25000.00 Y25000.00 Z2500.00 E2400.00 ; set maximum speeds (mm/min)
                M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
                M906 X300 Y300 Z300 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
                M84 S30 ; Set idle timeout

                ; Axis Limits
                M208 X0 Y0 Z0 S1 ; set axis minima
                M208 X440 Y535 Z900 S0 ; set axis maxima

                ; Endstops
                M574 X1 S1 P"!xstop" ; configure active-low endstop for high end on X via pin xstop
                M574 Y2 S1 P"!ystop" ; configure active-low endstop for high end on Y via pin ystop
                M574 Z1 S1 P"!zstop" ; configure active-low endstop for low end on Z via pin zstop

                ; Z-Probe

                ;M307 H7 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
                M950 S0 C"exp.heater7" ; create servo pin 0 for BLTouch
                M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
                G31 P500 X0 Y40.9 Z.445 ; set Z probe trigger value, offset and trigger height
                M557 X50:400 Y50:400 S100 ; define mesh grid x50:400 starts at 50, ends at 400 SXX moves by what its set to between points

                ; Heaters
                M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
                M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
                M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
                M140 H0 ; map heated bed to heater 0
                M143 H0 S120 ; set temperature limit for heater 0 to 120C
                M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
                M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
                M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

                ; Fans
                M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
                M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
                M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
                M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

                ; Tools
                M563 P0 D0 H1 F0 ; define tool 0
                G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                ; Custom settings are not defined

                ; Miscellaneous
                M575 P1 S1 B57600 ; enable support for PanelDue
                M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

                undefined 1 Reply Last reply 25 Aug 2020, 22:02 Reply Quote 0
                • undefined
                  tracar @Phaedrux
                  last edited by 25 Aug 2020, 22:01

                  @Phaedrux said in hbot homes correctly but prints mirrored ,:

                  M98 P"config.g"

                  M98 P"config.g"

                  HTTP is enabled on port 80
                  FTP is disabled
                  TELNET is disabled
                  Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C

                  1 Reply Last reply Reply Quote 0
                  • undefined
                    Phaedrux Moderator @tracar
                    last edited by 25 Aug 2020, 22:02

                    Try enabling the pullup resistor on the servo pin with the ^ before the pin name.

                    M950 S0 C"^exp.heater7" ; create servo pin 0 for BLTouch with pullup

                    Z-Bot CoreXY Build | Thingiverse Profile

                    undefined 1 Reply Last reply 25 Aug 2020, 22:05 Reply Quote 0
                    • undefined
                      tracar @Phaedrux
                      last edited by 25 Aug 2020, 22:05

                      @Phaedrux
                      ; Z-Probe

                      ;M307 H7 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
                      M950 S0 C"^exp.heater7" ; create servo pin 0 for BLTouch
                      M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
                      G31 P500 X0 Y40.9 Z.445 ; set Z probe trigger value, offset and trigger height
                      M557 X50:400 Y50:400 S100 ; define mesh grid x50:400 starts at 50, ends at 400 SXX moves by what its set to between points

                      nada.

                      1 Reply Last reply Reply Quote 0
                      • undefined
                        Phaedrux Moderator
                        last edited by 25 Aug 2020, 22:07

                        Try M950 S0 C"exp.31" ; create servo pin 0 for BLTouch

                        Z-Bot CoreXY Build | Thingiverse Profile

                        undefined 1 Reply Last reply 25 Aug 2020, 22:09 Reply Quote 0
                        • undefined
                          tracar @Phaedrux
                          last edited by 25 Aug 2020, 22:09

                          @Phaedrux
                          no change

                          undefined 1 Reply Last reply 25 Aug 2020, 22:10 Reply Quote 0
                          • undefined
                            peter247 @tracar
                            last edited by 25 Aug 2020, 22:10

                            @tracar
                            how are you testing that it is working ?

                            undefined 1 Reply Last reply 25 Aug 2020, 22:11 Reply Quote 1
                            • undefined
                              tracar @peter247
                              last edited by 25 Aug 2020, 22:11

                              @peter247

                              make the changes to config file, save ,reset board send command M280 P0 S10

                              undefined 1 Reply Last reply 25 Aug 2020, 22:15 Reply Quote 1
                              • undefined
                                Phaedrux Moderator
                                last edited by 25 Aug 2020, 22:12

                                Does it do a self test on bootup?

                                Z-Bot CoreXY Build | Thingiverse Profile

                                undefined 1 Reply Last reply 25 Aug 2020, 22:13 Reply Quote 0
                                • undefined
                                  tracar @Phaedrux
                                  last edited by 25 Aug 2020, 22:13

                                  @Phaedrux
                                  yes

                                  undefined 1 Reply Last reply 25 Aug 2020, 22:14 Reply Quote 1
                                  • undefined
                                    tracar @tracar
                                    last edited by 25 Aug 2020, 22:14

                                    @tracar so annoying lol:
                                    Error

                                    As a new user, you can only post once every 60 second(s) until you have earned 1 reputation - please

                                    1 Reply Last reply Reply Quote 1
                                    • undefined
                                      peter247 @tracar
                                      last edited by peter247 25 Aug 2020, 22:15

                                      @tracar

                                      How is the probe when you send it extended or retracted ?

                                      undefined 1 Reply Last reply 25 Aug 2020, 22:21 Reply Quote 1
                                      • undefined
                                        tracar @peter247
                                        last edited by 25 Aug 2020, 22:21

                                        @peter247
                                        does nothing

                                        undefined 1 Reply Last reply 25 Aug 2020, 22:24 Reply Quote 0
                                        • undefined
                                          peter247 @tracar
                                          last edited by 25 Aug 2020, 22:24

                                          @tracar

                                          Sorry , I was not clear what I was asking .
                                          When you set M280 P0 S10 , was the probe extended or retracted ?

                                          undefined 1 Reply Last reply 25 Aug 2020, 22:26 Reply Quote 0
                                          114 out of 169
                                          • First post
                                            114/169
                                            Last post
                                          Unless otherwise noted, all forum content is licensed under CC-BY-SA