Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    hbot homes correctly but prints mirrored ,

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    4
    169
    8.1k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Phaedruxundefined
      Phaedrux Moderator @peter247
      last edited by

      @peter247 said in hbot homes correctly but prints mirrored ,:

      M307 H7 A-1 C-1 D-1

      Will just be ignored in RRF3.

      If you send M98 P"config.g" do you get any errors echoed back?

      Z-Bot CoreXY Build | Thingiverse Profile

      tracarundefined 1 Reply Last reply Reply Quote 0
      • tracarundefined
        tracar @Phaedrux
        last edited by

        @Phaedrux
        ; Configuration file for Duet WiFi (firmware version 3)
        ; executed by the firmware on start-up
        ;
        ; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Aug 25 2020 08:01:23 GMT-0600 (Mountain Daylight Time)

        ; General preferences
        G31 X0 Y0 Z0 P25
        G90 ; send absolute coordinates...
        M83 ; ...but relative extruder moves
        M550 P"Duet2" ; set printer name
        M669 K1 ; select CoreXY mode

        ; Network
        M552 S1 ; enable network
        M586 P0 S1 ; enable HTTP
        M586 P1 S0 ; disable FTP
        M586 P2 S0 ; disable Telnet

        ; Drives
        M569 P5 S0 T5 R1 ; physical drive y goes forwards
        M569 P6 S1 T5 R1 ; physical drive x goes forwards
        M569 P7 S1 T5 R1 ; physical drive z goes forwards
        M569 P8 S1 T5 R1 ; physical drive z2 goes forwards
        M569 P3 S1 ; physical drive extruder goes forwards
        M584 X6 Y5 Z7:8 E3 ; set drive mapping
        M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
        M92 X200.00 Y200.00 Z200.00 E138.23 ; set steps per mm
        M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
        M203 X25000.00 Y25000.00 Z2500.00 E2400.00 ; set maximum speeds (mm/min)
        M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
        M906 X300 Y300 Z300 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
        M84 S30 ; Set idle timeout

        ; Axis Limits
        M208 X0 Y0 Z0 S1 ; set axis minima
        M208 X440 Y535 Z900 S0 ; set axis maxima

        ; Endstops
        M574 X1 S1 P"!xstop" ; configure active-low endstop for high end on X via pin xstop
        M574 Y2 S1 P"!ystop" ; configure active-low endstop for high end on Y via pin ystop
        M574 Z1 S1 P"!zstop" ; configure active-low endstop for low end on Z via pin zstop

        ; Z-Probe

        ;M307 H7 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
        M950 S0 C"exp.heater7" ; create servo pin 0 for BLTouch
        M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
        G31 P500 X0 Y40.9 Z.445 ; set Z probe trigger value, offset and trigger height
        M557 X50:400 Y50:400 S100 ; define mesh grid x50:400 starts at 50, ends at 400 SXX moves by what its set to between points

        ; Heaters
        M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
        M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
        M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
        M140 H0 ; map heated bed to heater 0
        M143 H0 S120 ; set temperature limit for heater 0 to 120C
        M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
        M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
        M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

        ; Fans
        M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
        M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
        M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
        M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

        ; Tools
        M563 P0 D0 H1 F0 ; define tool 0
        G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
        G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

        ; Custom settings are not defined

        ; Miscellaneous
        M575 P1 S1 B57600 ; enable support for PanelDue
        M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

        Phaedruxundefined 1 Reply Last reply Reply Quote 0
        • tracarundefined
          tracar @Phaedrux
          last edited by

          @Phaedrux said in hbot homes correctly but prints mirrored ,:

          M98 P"config.g"

          M98 P"config.g"

          HTTP is enabled on port 80
          FTP is disabled
          TELNET is disabled
          Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C

          1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator @tracar
            last edited by

            Try enabling the pullup resistor on the servo pin with the ^ before the pin name.

            M950 S0 C"^exp.heater7" ; create servo pin 0 for BLTouch with pullup

            Z-Bot CoreXY Build | Thingiverse Profile

            tracarundefined 1 Reply Last reply Reply Quote 0
            • tracarundefined
              tracar @Phaedrux
              last edited by

              @Phaedrux
              ; Z-Probe

              ;M307 H7 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
              M950 S0 C"^exp.heater7" ; create servo pin 0 for BLTouch
              M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
              G31 P500 X0 Y40.9 Z.445 ; set Z probe trigger value, offset and trigger height
              M557 X50:400 Y50:400 S100 ; define mesh grid x50:400 starts at 50, ends at 400 SXX moves by what its set to between points

              nada.

              1 Reply Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator
                last edited by

                Try M950 S0 C"exp.31" ; create servo pin 0 for BLTouch

                Z-Bot CoreXY Build | Thingiverse Profile

                tracarundefined 1 Reply Last reply Reply Quote 0
                • tracarundefined
                  tracar @Phaedrux
                  last edited by

                  @Phaedrux
                  no change

                  peter247undefined 1 Reply Last reply Reply Quote 0
                  • peter247undefined
                    peter247 @tracar
                    last edited by

                    @tracar
                    how are you testing that it is working ?

                    tracarundefined 1 Reply Last reply Reply Quote 1
                    • tracarundefined
                      tracar @peter247
                      last edited by

                      @peter247

                      make the changes to config file, save ,reset board send command M280 P0 S10

                      peter247undefined 1 Reply Last reply Reply Quote 1
                      • Phaedruxundefined
                        Phaedrux Moderator
                        last edited by

                        Does it do a self test on bootup?

                        Z-Bot CoreXY Build | Thingiverse Profile

                        tracarundefined 1 Reply Last reply Reply Quote 0
                        • tracarundefined
                          tracar @Phaedrux
                          last edited by

                          @Phaedrux
                          yes

                          tracarundefined 1 Reply Last reply Reply Quote 1
                          • tracarundefined
                            tracar @tracar
                            last edited by

                            @tracar so annoying lol:
                            Error

                            As a new user, you can only post once every 60 second(s) until you have earned 1 reputation - please

                            1 Reply Last reply Reply Quote 1
                            • peter247undefined
                              peter247 @tracar
                              last edited by peter247

                              @tracar

                              How is the probe when you send it extended or retracted ?

                              tracarundefined 1 Reply Last reply Reply Quote 1
                              • tracarundefined
                                tracar @peter247
                                last edited by

                                @peter247
                                does nothing

                                peter247undefined 1 Reply Last reply Reply Quote 0
                                • peter247undefined
                                  peter247 @tracar
                                  last edited by

                                  @tracar

                                  Sorry , I was not clear what I was asking .
                                  When you set M280 P0 S10 , was the probe extended or retracted ?

                                  tracarundefined 1 Reply Last reply Reply Quote 0
                                  • tracarundefined
                                    tracar @peter247
                                    last edited by

                                    @peter247
                                    afyer it does the initial test upon powering up, the pin is always up,

                                    pin up or pin down commands do no change, it remains up

                                    peter247undefined 1 Reply Last reply Reply Quote 0
                                    • peter247undefined
                                      peter247 @tracar
                                      last edited by

                                      @tracar

                                      Stupid question I know , have you checked the wiring ?
                                      that all the wires are contacting ?

                                      tracarundefined 1 Reply Last reply Reply Quote 0
                                      • tracarundefined
                                        tracar @peter247
                                        last edited by

                                        @peter247 yes. all good, even replaced with a new harness to test , all good

                                        peter247undefined 1 Reply Last reply Reply Quote 0
                                        • peter247undefined
                                          peter247 @tracar
                                          last edited by

                                          @tracar

                                          Hell if I know what wrong !!
                                          The only thing I can think of is changing the heater pin ,
                                          with M950 S0 C"exp.heater7" and changing the physical pin.
                                          But if it worked before I can see that working too !!!

                                          peter247undefined 1 Reply Last reply Reply Quote 0
                                          • peter247undefined
                                            peter247 @peter247
                                            last edited by

                                            This post is deleted!
                                            tracarundefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA