Duet 3 : No tool nor bed shown

Donpi

@engikeneer M115 return this :

jay_s_uk

@Donpi I would upgrade your firmware to 3.1.1 first.
https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware
https://github.com/Duet3D/RepRapFirmware/releases/tag/3.1.1

Donpi

@droftarts

I use a Raspberry 4 2Go as SBC.

M98 P"config.g" Show me the welcome message again.
But no error

Here is the return of
M308 S0
M308 S1
M950 S0
M950 S1

M122 returns this :

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.01-RC9 running on Duet 3 MB6HC v1.01 or later
Board ID: 08DJM-956BA-NA3TN-6JTDG-3SD6J-TABLTUsed output buffers: 1 of 40 (11 max)
=== RTOS ===
Static ram: 154572
Dynamic ram: 160680 of which 20 recycled
Exception stack ram used: 264
Never used ram: 77680
Tasks: NETWORK(ready,2076) HEAT(blocked,1412) CanReceiv(suspended,3824) CanSender(suspended,1484) CanClock(blocked,1432) TMC(blocked,216) MAIN(running,5036) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 00:03:46 ago, cause: power up
Last software reset details not available
Error status: 0
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 20.8, current 26.6, max 26.8
Supply voltage: min 24.9, current 24.9, max 25.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
Driver 0: standstill, reads 6924, writes 11 timeouts 0, SG min/max 0/0
Driver 1: standstill, reads 6925, writes 11 timeouts 0, SG min/max 0/0
Driver 2: standstill, reads 6925, writes 11 timeouts 0, SG min/max 0/0
Driver 3: standstill, reads 6926, writes 11 timeouts 0, SG min/max 0/0
Driver 4: standstill, reads 6926, writes 11 timeouts 0, SG min/max 0/0
Driver 5: standstill, reads 6927, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2020-11-18 12:04:16
Slowest loop: 3.26ms; fastest: 0.14ms
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0 0, running macro
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 1.90ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8
- Ethernet -
State: disabled
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 0, longest wait 0ms for type 0
=== Linux interface ===
State: 0, failed transfers: 0
Last transfer: 17ms ago
RX/TX seq numbers: 6649/6650
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.1.1
Daemon:
Finishing macro daemon.g, started by system
> Next stack level
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 0.82

Donpi

@jay_s_uk
you meen with with
sudo apt update
sudo apt upgrade

I'll allready done it but noting install.

A Former User

@Donpi said in Duet 3 : No tool nor bed shown:

I'll allready done it but noting install.

try running M997 the previous post shows the software on the pi is 3.1.1. M997 should try to flash the board to match.

Donpi

@bearer @jay_s_uk @engikeneer
The M997 worked... I guess
now M115 reutrns :

But still nothing...

Veti

@Donpi said in Duet 3 : No tool nor bed shown:

M950 S0
M950 S1

you wrote T instead of S

Donpi

@Veti Yeah, in this case, even S was wrong

M950 H0 and H1 give the same response :
Heater 0 does not exist

Veti

@Donpi said in Duet 3 : No tool nor bed shown:

M350 X16 Y16 Z16:16 E16 I1 ; Configure microstepping with interpolation

you are not allowed to specify 2 z values.

what i would suggest is. save all your config files and generate an new one from the configurator.
then slowly start adding your additional configs one by one until it breaks.

droftarts

@Donpi My mistake, send M950 H0 and M950 H1 (not T0/1) to check heater definition. Also send M563 P0 to check tool definition.

M563 P0
Tool 0 - name: T0; drives: 0; heaters (active/standby temps): 1 (0.0/0.0); xmap: X; ymap: Y; fans: 0; status: selected

But M308 S0 and S1 reporting "Sensor does not exist" does seem to imply there is a problem with your M308 definition in config.g. What happens if you send M308 S0 P"temp0" Y"thermistor" A"Bed Temp" T100000 B4700 C0.0000000706?

Ian

Donpi

@droftarts strange this work well.
and if I call M308 S0, it says :
Sensor 0 (bed Temp) type bla bla bla...

It's like my config.g is not readed or somthing reset everything

Donpi

@Veti With a complettely new copnfiguration strait from the generator I have the same behaviour

Veti

what version of the duet web control are you running?

Donpi

@Veti
I'am a bit puzzled ...

I have created a macro with my config.g.
And running the macro I get the tootls and heaters...
It' just give me this errors

I don't know why my config.g is ignored...

Donpi

@Veti My duet web control is 3.1.1

Donpi

Hum the macro is not saved in the micro SD ... I think the problem is from here ...

droftarts

@Donpi If you're using SBC, you shouldn't have an SD card in the Duet! The O: directory is a virtual SD drive on the Raspberry Pi. See https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_Virtual_SD_card

Where is your config.g? On the SD card in the Duet, or on the Raspberry Pi?

Ian

Donpi

@droftarts
Of cours in the raspberry
There is no card on de Duet

Donpi

Hooo... could it be that the partition I see on windows is the one for the Duet in standalone mode.
And that the partition use by the Raspberry Bi is not visible on windows ?

droftarts

@Donpi said in Duet 3 : No tool nor bed shown:

Hooo... could it be that the partition I see on windows is the one for the Duet in standalone mode.
And that the partition use by the Raspberry Bi is not visible on windows ?

Very likely!

Ian