Hello,
The SKR1.4 and yeah I read about the possibility of running RRF on it but as I'm already running the 6HC on my Ender 5 Plus and that I'm quite happy with it, I said to myself, go for it
Hello,
The SKR1.4 and yeah I read about the possibility of running RRF on it but as I'm already running the 6HC on my Ender 5 Plus and that I'm quite happy with it, I said to myself, go for it
@Falcounet @Herve_Smith
Hi, Thanks for taking the time to reply, actually I ended up answering my question earlier a couple of hours ago and have been finishing the printer configuration. the cable in question if anyone else looks fo the info in the future is the filament sensor.
Concerning the RPI, I'll be running the printer with Klipper not with original firmware hence why the RPI is requiered in my case.
I now got everything working as expected including the filament sensor so all well and good; again appreciate your time replying, especially that it was a dumb prep error on my side when I starting labelling and unpluging the cables from the SKR.
Anyone using a Duet 3 mini with an Artillery Sidewinder that could point in me in the right direction please?
Thanks
Hi all,
After several years using a Duet 3 6HC in my ender 5 Plus, I've replaced the Duet 3 6HC with a duet 3 mini 5+ and I'm saving the Duet 3 6HC for a future project. In the past I posted here my project of replacing an SKR 1.4 turbo with the Duet3 6HC, after long time hesitating and with the duet 3 mini giving great results on the Ender 5+, I decided to pull the gun en replace the SKR with the mini.
That being said, I've starting cabling the new board to the artillery, I believe that I'm mostly done but I'm having some issues identifying some of the cables; I have an adapter on a white cable that you can see at the bottom right of the image.
Can someone please confirm what the white cable is and where should it be plugged in also(I completely forgot to label it ), is any one also using a BL touch or a super pinda with the sidewinder x1 ?
Also I believe I can power up a raspberry pi from one of the 5V connectors if so what would be the best pins to use in this case??
FYI, I have no screen connected.
Thanks in advance for your help.
Thanks for the feedback guys, I'll retune my slicer settings and see what comes out and use a temp tower to nail the ebst printing temps for the filament being used. I'm also considering moving from Simplify3D to either PrusaSlicer or SuperSlicer once I get the new settings nailed in.
May I ask you what your slicer settings are for the Hemera please? I've done 3 prints trying to nailed settings down but I still have some issues as you can see in the images below:
The first print was the calibration cube on the right then the one on the left and finally the benchy. I'm using Simplify3d and between the first and second cube I raised the temperature from 210 to 235 and disabled retraction so layer adhesion was better but needs to be improved.
If I compare the benchy to one of the one printed with the previous setup using the Microswiss Direct drive setup, I wasn't expecting the difference to be so huge, not sure why but I hoping that the changes required on the slicer would be minimal but I was complety wrong
Current setting after disabling retraction, the extrusion multiplier was raised from 0.90 to 0.95 and the extrusion witdth was changed form manual .0.40 to Auto, Coasting and Nozzle wipe are enable .
Layer height is set to 0.32
Any suggestions?
Thanks
@rjenkinsgb spot on!
Thanks, that was it, extrusion working fine, really appreciate your help on this.
Hi @rjenkinsgb,
Thanks for taking the time to reply, I have M83 setup in my general preferences in my config.g as per below, so not sure if that changes anything or if maybe I need to replace it with M82 instead,:
General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Ender 5 Plus" ; set printer name
Also, it seems that I'm using the same E409 steps/mm, E16 and I1 values as you are so I'm a bit confused to be honest.
Concerning directions I'll keep it as S1which is extruding.
Hi all,
I'm having an issue on my Ender 5 Plus when trying to calibrate the extrusion following the replacement of a Microswiss hotend with a Hemera, I'm using a Duet 3 board the normal one not the mini.
When sending a G1 E100 F3000 command in the console I just get about 4,5mm extruded.
I believe the changes on config.g to be correct but I'm clearly missing something or my Hemera is faulty:
; Drives
M569 P0.0 S0 ; physical drive 0.0 goes backwards
M569 P0.1 S0 ; physical drive 0.1 goes backwards
M569 P0.2 S0 ; physical drive 0.2 goes backwards
M569 P0.4 S1 ; physical drive 0.4 goes backwards
M584 X0.0 Y0.1 Z0.2:0.3 E0.4 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E409 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z1200.00 E3600.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E5000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
I changed the S value to 1 on the M569 P0.4 line in order to get the filament extruded but I must admit that I was surprised I had to do this, as it was working fine with the previous motor, so maybe that the hemera motor is setup to turn in the other direction, this is the only thing I can think of right now.
Anyone one has an idea of what I'm missing here, I'll appreciate any insight !
Thanks
Hello,
Nothing at first sight, bed look flat to me but what I can say is that the first layer sticks better in the middle and back and also on the front right side, I'm a bit far on the left corner, so need to redo my manual bed level again. This is using the stock bltouch with the stock mount but not the stock glass bed as I replaced it with TH3D EzFlex smooth PEI and a magnetic base
just tried it and I'm no longer getting the error but now I'm a bit concerned about the results, not sure if this is good or not: