Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. drthomasw3
    3. Topics
    • Profile
    • Following 0
    • Followers 0
    • Topics 9
    • Posts 38
    • Best 1
    • Controversial 0
    • Groups 0

    Topics created by drthomasw3

    • drthomasw3undefined

      Bltouch with dual z endstops

      Tuning and tweaking
      • • • drthomasw3
      2
      0
      Votes
      2
      Posts
      184
      Views

      Phaedruxundefined

      Can you post your config and homing files as you have them setup right now?

      Also a bit more information about your printer, what firmware and duet you're using would be nice too.

    • drthomasw3undefined

      Duet control no longer shows in the browser

      Duet Web Control
      • • • drthomasw3
      28
      0
      Votes
      28
      Posts
      1.6k
      Views

      drthomasw3undefined

      Reloading the www files to new version 2.07 worked. I guess corruption is everywhere.
      Thank you all!

    • drthomasw3undefined

      After installing dual z stops heater gone

      Tuning and tweaking
      • • • drthomasw3
      10
      0
      Votes
      10
      Posts
      276
      Views

      drthomasw3undefined

      Thanks to all changing the tool number worked!

    • drthomasw3undefined

      Adding dual z stops

      Tuning and tweaking
      • • • drthomasw3
      4
      0
      Votes
      4
      Posts
      218
      Views

      drthomasw3undefined

      Solved
      G1 Z2 F6000 changed to G1 S2 Z2 F6000

    • drthomasw3undefined

      Screen dark after Firmware update

      PanelDue
      • • • drthomasw3
      2
      0
      Votes
      2
      Posts
      147
      Views

      droftartsundefined

      What is the filename of the firmware you used? How did you upload the firmware, with BOSSA as in https://duet3d.dozuki.com/Wiki/PanelDue_Firmware_update ?

      Did you check the Erase all, Lock, and Boot from flash boxes?

      Ian

    • drthomasw3undefined

      Duet 2 WiFI / Bl Touch with Tronxy X5SA

      General Discussion
      • • • drthomasw3
      4
      0
      Votes
      4
      Posts
      425
      Views

      drthomasw3undefined

      Resolved? Repeatable z=0 after repeated trigger hight calibration random results som good prints many bad due to the initial layer height
      I remounted the BL Touch to make sure the bottom collar was 8.3mm above the table. I reset the trigger height using Max Nippard's 10/27/2018 suggestions on the https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe page His suggestions made much more sense than the page content. My only issue was that he stated, "your trigger height result (should be between 0 and 1mm, depending on your printer." My trigger height was 2.16mm. But it works! I also changed my P5 Back to P9.

      A constant error that does not affect the ability to print except mesh values do not seem to be used
      This error was caused by G code script added by my slicer Simplified 3D after editing that error is gone.☺

      Heating fault at first just when heating from room temp. E3D Lite hot end with 24 v cartridge. ran Autotune but the error continues
      ?? It seems fixed: I replaced the thermistor and changed out the aluminum block for a copper one. Copper maintains heat better but for the same reason, It takes longer to heat (pure desperation). I then ran autotune again remembering to do an M500 afterward. A word of caution to anyone reading this and deciding to use the M307 for heater parameters in the config.g; Do not forget to comment out the M307 for that heater in config-overide.g If you want the new settings to be used by the firmware.
      I would appreciate comments on the 2.16 trigger height.
      Thank you very much for your direction.
      Tom

    • drthomasw3undefined

      Updated to firmware 2.03 WiFi not working

      Firmware installation
      • • • drthomasw3
      7
      0
      Votes
      7
      Posts
      352
      Views

      drthomasw3undefined

      Thank you!!!!!!!!!

    • drthomasw3undefined

      Z axis movement

      Tuning and tweaking
      • • • drthomasw3
      14
      0
      Votes
      14
      Posts
      826
      Views

      Phaedruxundefined

      please upload your actual homing files rather than copy and paste.