Posts made by Fedekossel1

It used to work perfectly, strangely now it's stopped. Now I read again this link that you posted to me.

hi, lately i'm having problems with self-leveling, i run the g32 perfectly with smart effector, after step to the g29 for the mesh, towards the last touches it slams the nozzle over the bed and stops, I checked all the cables with the tester are ok.

another problem that I'm having, during the press it doesn't respond to babysteps, it doesn't get up and it doesn't go down.

I attach my configuration

configurazione.txt

Duet Web Control 2.1.3
Board: Duet WiFi 1.02 or later (duetwifi102)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 2.05.1 (2020-02-09b1)
Duet WiFi Server Version: 1.23

config.g :
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Mon Apr 20 2020 15:09:48 GMT+0200 (Ora legale dell’Europa centrale)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"kossel" ; set printer name
M665 R185 L360.27 B150 H371 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z160.00 E830.00 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E700 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 Z0 S1 ; set minimum Z

; Endstops
M574 X2 Y2 Z2 S1 ; set active high endstops

; Z-Probe
M558 P5 R0.4 H5 F500 T5000 ; set Z probe type to effector and the dive height + speeds
G31 P100 X0 Y0 Z-0.175 ; set Z probe trigger value, offset and trigger height
M557 R120 S20 ; define mesh grid

; Heaters
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4092 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans

M106 P0 S0 I0 F500 H-1 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501 ; load saved parameters from non-volatile memory

config.override

; config-override.g file generated in response to M500 at 2020-05-19 05:01
; This is a system-generated file - do not edit
; Delta parameters
M665 L360.270:360.270:360.270 R185.199 H368.562 B150.0 X0.282 Y0.051 Z0.000
M666 X1.313 Y-0.872 Z-0.441 A0.00 B0.00
; Heater model parameters
M307 H0 A157.6 C626.6 D2.2 S1.00 V24.7 B0
M307 H1 A648.3 C115.7 D5.6 S1.00 V24.6 B0
M307 H2 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H3 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H4 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H5 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H6 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H7 A340.0 C140.0 D5.5 S1.00 V0.0 B0
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00

Version 2.05, With old versions I didn't have this problem.

Hello, strangely something strange happens to me, after editing the config.g file the changes made are not made by the duet, I realized that I have to edit the config.g.bak file as well,Just so the duet makes the changes I changed on the config.g, I tried to delete the config.g.bak file as soon as I turn off no longer starts And it doesn't connect to the wifi network, I put the config.g.bak file back into the memory and the Card works normally. What happened?

@giostark That's right, I have the same blobs of this discussion that you linked to me

@Phaedrux Tomorrow morning I'll put all the necessary information

@giostark As soon as every perimeter that does at any height starts, the perimeter begins with too much material but only where the retraction begins, to better understand along the entire seam.

@giostark I use smart effector leveling is very precise, I have a nozzle from 0.4 and use volcano

@bot In any case, you highlight the problem I have very swollen seams

@Phaedrux Is it normal that activating the M572 command makes a strange noise? It's very annoying

Hello, I have a problem with my delta, I say that I did all the tests of the step mm E and many tests on the slicer but the situation does not change, I have problems of excessive material at the beginning of the perimeter even if I decrease the flow the result does not change. Is there any parameter where you can adjust this problem? I use a direct system. I noticed that the seam is very swollen.

I just set all the axes correctly to 16 microsteps interpolated to 256, with the same gcode that froze, now goes without stopping. I keep you updated these days if I get problems or blocks during printing. At the moment I thank everyone!

@dc42
I fixed, it's normal that it doesn't tell me giving the command M350 "example" X:16 (on),
?
From config I put
M350 X16 Y16 Z16 E16 I1

Typing the M350 command gives me this result

M350
Microstepping - X:16, Y:16, Z:16, E:16:16```

I found inside config.g.bak all the steps at 256 microsteps, I change them to 16?

@jay_s_uk
I just tried, I always 256 microsteps, besides the config are in other places the parameters of microsteps?

@AndreS
; config-override.g file generated in response to M500 at 2020-03-10 10:27
; This is a system-generated file - do not edit
; Delta parameters
M665 L360.270:360.270:360.270 R185.353 H364.129 B150.0 X0.229 Y0.060 Z0.000
M666 X1.793 Y-1.094 Z-0.699 A0.00 B0.00
; Heater model parameters
M307 H0 A90.0 C700.0 D10.0 S1.00 V0.0 B1
M307 H1 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H2 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H3 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H4 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H5 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H6 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H7 A340.0 C140.0 D5.5 S1.00 V0.0 B0
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00

@dc42 I just did the M350 command. Oddly enough, it gives me this result

Microstepping - x:256, y:256, z:256, e:16:16

In my configuration posted above I clearly put 16 interpolated microsteps at 256, excluding extruder that I will now also put at 256 interpolation,

@Phaedrux I have to give the command M350 Just freezes?

Hi guys, lately I've been having some serious problems with my delta, for no reason it stops during the press. I have a version 2.05, and web control 2.07 At first I read a discussion of a user who specified the problem was due to 256 microsteps, I had 256 microsteps so I put 16 microsteps interpolation to 256. But the result has not changed. I always have those blocks, everything stays on even the fans, I can only use the emergency stop button. I also replaced the sd memory with a quality thinking it might be there the problem, Place here my configuration

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.0.4 on Tue Oct 01 2019 19:52:44 GMT+0200 (hora de verano de Europa central)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"kossel" ; set printer name
M665 R185 L360.27 B150 H365 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S1 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards

M350 X16 Y16 Z16 I1 ; Configure microstepping with interpolation
M350 E16 I0 ; Configure microstepping without interpolation
M92 X160 Y160 Z160 ; Set steps per mm for X,Y and Z
M92 E830 ; Set steps per mm for Extruder

M566 X1000.00 Y1000.00 Z1000.00 E900.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X900.00 Y900.00 Z900.00 E800.00 ; set accelerations (mm/s^2)
M906 X1700 Y1700 Z1700 E1100 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 Z0 S1 ; set minimum Z

; Endstops
M574 X2 Y2 Z2 S1 ; set active high endstops

; Z-Probe
M558 P8 R0.4 H5 F800 T3000 ; set Z probe type to effector and the dive height + speeds
G31 P100 X0 Y0 Z-0.21 ; set Z probe trigger value, offset and trigger height
M557 R120 S20 ; define mesh grid

; Heaters
M305 P0 T100000 B4092 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T40 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0 I0 F500 H-1 ; electronic fan
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501 ; load saved parameters from non-volatile memory

---

Diagnosis command
M122
=== Diagnostica ===
RepRapFirmware per Duet 2 WiFi / Ethernet versione 2.05 in esecuzione su Duet WiFi 1.02 o successivo
ID scheda: 08DGM-9T6BU-FG3SW-6J9FD-3SN6M-TVSZG
Buffer di output usati: 1 di 24 (15 max)
= == RTOS ===
Ram statico: 25712 Ram
dinamico: 92620 di cui 380
ram di stack di eccezioni riciclati usati: 448
Ram mai usati: 11912
Compiti: NETWORK (pronto, 628) HEAT (bloccato, 1232) MAIN (in esecuzione, 348) IDLE (pronto, 160)
Mutex di proprietà:
=== Piattaforma ===
Ultimo ripristino 00:14:21 fa, causa: accensione
Ultimo ripristino del software al 2020-03-08 12:35, motivo: Utente, modulo di rotazione GCodes, disponibile RAM 11896 byte (slot 3)
Codice di reimpostazione software 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Stato errore: 10
voci file libere
rilevate : 9 Scheda SD 0 rilevata, velocità interfaccia: 20,0 MByte / sec
tempo di scrittura blocco più lungo: 235 ms 0,7
Temperatura MCU: min 44,3, corrente 53,0, max 53,2
Tensione di alimentazione: min 24,5, corrente 24,7, max 24,8, eventi di sottotensione: 0, eventi di sovratensione: 0, alimentazione buona: sì
Driver 0: fermo, SG min / max 0 / 99
Driver 1: fermo, SG min / max 0/97
Driver 2: fermo, SG min / max 0/103
Driver 3: fermo, SG min / max 0/1023
Driver 4: fermo, SG min / max non disponibile
Data / tempo: 2020-03-08 13:26:45
Conteggio risultati dati cache 2063208117 Ciclo
più lento: 1256,78 ms; più veloce: 0,07 ms
errori I2C nak 0, invio timeout 0, ricezione timeout 0, finishTimeout 0, reset 0
=== Move ===
singhiozzo: 363416, FreeDm: 90, MinFreeDm: 84, MaxWait: 306358ms
Compensazione del letto in uso: nessuna , comp offset 0.000
=== DDARing ===
Mosse pianificate: 2350, mosse completate: 2310, StepErrors: 0, LaErrors: 0, Underruns: 0, 1
=== Heat ===
Riscaldatori del letto = 0 -1 -1 - 1, ChamberHeaters = -1 -1 Il
riscaldatore 0 è acceso, I-accum = 0,0 Il
riscaldatore 1 è acceso, I-accum = 0.3
=== GCodes ===
Segmenti rimasti: 1
Record stack: 2 allocati, 0 in uso
Blocco movimento detenuto da null
http è inattivo negli stati 0
telnet è inattivo negli stati 0 Il
file sta eseguendo "G1 X-23.857 Y19.214 E0.0409" in stato (s) 0
seriale è inattivo in stato (s) 0
aux è inattivo in stato (s) 0
demone è inattivo negli stati 0 la
coda è inattiva negli stati 0 l'
autopausa è inattiva negli stati 0 La
coda del codice è vuota.
=== Rete ===
Ciclo più lento: 1257,00 ms; più veloce: 0,08 ms
Stati del risponditore: HTTP (0) HTTP (0) HTTP (0) HTTP (0) FTP (0) Telnet (0) Telnet (0)
Sessioni HTTP: 1 di 8

WiFi -
Stato della rete in esecuzione Il
modulo WiFi è collegato al punto di accesso
Messaggi non riusciti: in attesa 0, non già 0, noresp 1
Versione firmware
WiFi 1.23 Indirizzo MAC WiFi ec: fa: bc: 31: 7e: cd
WiFi Vcc 3.37, motivo di ripristino Acceso dal processore principale
Dimensione flash WiFi 4194304, heap gratuito 23296
Indirizzo IP WiFi 192.168.43.42
Potenza del segnale WiFi -50dBm, riconnessioni 0, modem in modalità sospensione
Stati socket: 0 0 0 0 0 0 0 0

@BlueDust This M122 that I posted is already with microsteps, and updated steps to 16 interpolation 256, I will do a new discussion. Thank you