Posts made by itsab67

Can two panel dues be connected to the duet wifi and display at the same time?

@Phaedrux

My friend i appreciate the time you have spent trying to help. However it appears nothing was wrong. i had a close look at the bltouch and discovered there was a string of PETG wrapped around the bltouch pin, once i removed that all works as it should. Cant believe i didn't notice that earlier.

config.json

also this, not sure if helps you

@Phaedrux

here they are

; deployprobe.g
; called to deploy a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.1.8 on Fri Nov 20 2020 16:34:34 GMT-0500 (Eastern Standard Time)
M280 P0 S10 ; deploy BLTouch

; retractprobe.g
; called to retract a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.1.8 on Fri Nov 20 2020 16:34:34 GMT-0500 (Eastern Standard Time)
M280 P0 S90 ; retract BLTouch

@Phaedrux yes, im using the ones that reprap config created.

Hi i just upgraded my Duet Ethernet to the newest reprap firmware 3.x
Before i was using reprap 2.x and my BLTouch worked good. I have not changed any connections. I've included my config.g and how i have the BLTouch wired, hoping someone can figure out what i did wrong. I used the reprap config tool. When I 1st turn on the printer the bltouch glows red, the probe deploys and retracts and then it sits there flashing red , it doesn't respond when i try to deploy or retract from the console and resetting the bltouch from the console doesn't help.

Config.g

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.8 on Fri Nov 20 2020 16:34:34 GMT-0500 (Eastern Standard Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"TLM" ; set printer name
M665 R160 L437 B160 H250 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E407.63 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1250 Y1250 Z1250 E1000 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 Z0 S1 ; set minimum Z

; Endstops
M574 X2 S1 P"xstop" ; configure active-high endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop
M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop

; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
M558 H30 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 R155 S20 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S90 ; set temperature limit for heater 0 to 90C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1 T45 ; set fan 2 value. Thermostatic control is turned on

; Tools
M563 P0 S"Hotend" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

@jay_s_uk thank you, i will look again, i must have missed them.

Is it possible to use the smart effector with regular bearing type rods instead of the magnetic rods. My bearing type rods are tight and have no slop. Obviously I would have to figure a way to mount them to the smart effector which was designed to work with the magnetic ball ends.
Any thoughts, has anyone done this or will the smart effector only be effective with the magnetic ball ends?

When i press upload & start (top right of web Interface) , it uploads the file, then sits and sits and does nothing, i have to cycle power to get control back, if i upload file from the G-Codes Files section, everything works as always. Is this Upload & Start feature broken or do i need do do something? (i have tried on several different files, and file sizes.![alt text]

@phaedrux Please explain pressure advance, is this a setting in S3D or in the config file?

I have the 7" integrated paneldue display. I send it some gcode to make to buzzer sound (M300 P500 S1000) and i can hardly hear it, when i adjust the volume under settings.... volume 0 or all the way up to volume 5 the volume dosent change. I want to use this buzzer as a end of print alarm, but the volume of it makes it useless. perhaps im missing something because adjusting the volume seems to make no difference in how loud it is. any ideas?

do the Maestro and wifi/ethernet boards use the same firmware?

24v power supply, and im not certain of the stepper motor specifications

I want to upgrade my Tevo little monster delta printer, which would be the better choice, a Duet Ethernet or a Duet Maestro?