@pm7399 You have a total of 4 posts on here none of which are in a thread started by you.
You can't expect help if you don't ask for it, in the correct polite way. Myself and others are more than happy to spend our own free time to help but show some respect.
Firstly, what board do you have? What printer? Give us details of the actual problem.
J.
@shiga I'd imagine people will only tell you where to buy a genuine Duet product and without knowing where you are located that's not going to be possible.
The duet website lists the official resellers. https://www.duet3d.com/page/genuine-resellers
Hi all,
So I thought as I'm now a Duet3D convert I should post my new printer build. First this to say it's still very much a work in progress, it's going to be an iDEX printer but currently only has one tool carriage installed, while I get to grips with the firmware side of things. This is my first Duet3D board so it's be a learning experience but once I got my head around it, it's going well.
So spec are currently,
Duet 3 0.6 with 3.1.1 firmware with a raspberry pi 3B attached.
300mm on X, 270mm on Y and 300mm on Z.
It has a Prusa MK3 extruder on a magnetic carriage system, allowing for quick hotend swaps.
E3D V6 hotends 24v.
700W Keenovo 240V AC bed attached to a 5mm Aluminium Tooling Plate.
Bed leveling is via a PINDA v1 from my old MK2.
So when I say it's a D-Bot/CrusaXY mash up that basically means I used my 300mm D-Bot (Link) for parts to make the printer designed by Hunter Bernstein on thingiverse (Link). The parts I printed are version 1 and they have been updated but I'm going to use this for now. The idea behind Hunter's design is to use a Creality3D CR-10 S5 and convert it to an iDEX printer, I didn't have a CR-10 so when the D-Bot conversion route.
So on to some pictures, I will be updating this thread as I add the extra tool etc but for now this is what it looks like.
So as you can see I'm using a quick disconnect extruder board, these are connected with a 26pin ribbon cable and so far works great, I remixed some things of thingiverse to make a bracket that holds the cable and I used some flat 9.5x0.3mm spring steel to support the cable (Like the E3D tool changer)
Well that's about it for now, I'll post updates soon.
Thanks,
James.
@markz the other pins aren't soldered in by default now.
First few prints off the printer.
@deckingman they are heat press inserts, used a lot by the Voron community. You use a soldering iron to push them in, some have even created jigs to hold the iron, you can also get new tips to better hold the insert.
Hi,
First you have two M584 commands in you're config.g.
M584 X0 Y1 Z2 E3
M584 X0 Y1 Z2:4 E
You also have (,) in you're M92 command.
M92 X80.00 Y80.00 Z634,5 E387,37.00
These need to be (.).
E3D thermistors are configured like this, T100000 B4725 C7.06e-8
Thank you, it wasn't until after I made the thread I realised there was a better category but couldn't change it myself?
What about your bridge fan settings?
I had mine setup as Input PIN io7.in & PWM Control Channel (BLTouch only) as io7.out, NO Modulation Pin.
And follow the wiring here, https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_BLTouch
Output from sudo journalctl -u duetcontrolserver
Mar 18 10:37:49 duet3 systemd[1]: duetcontrolserver.service: Failed with result 'protocol'.
Mar 18 10:37:49 duet3 systemd[1]: Failed to start Duet Control Server.
Mar 18 10:37:49 duet3 systemd[1]: duetcontrolserver.service: Service RestartSec=100ms expired, scheduling restart.
Mar 18 10:37:49 duet3 systemd[1]: duetcontrolserver.service: Scheduled restart job, restart counter is at 5.
Mar 18 10:37:49 duet3 systemd[1]: Stopped Duet Control Server.
Mar 18 10:37:49 duet3 systemd[1]: Starting Duet Control Server...
Mar 18 10:37:49 duet3 DuetControlServer[1141]: Duet Control Server v3.3.0
Mar 18 10:37:49 duet3 DuetControlServer[1141]: Written by Christian Hammacher for Duet3D
Mar 18 10:37:49 duet3 DuetControlServer[1141]: Licensed under the terms of the GNU Public License Version 3
Mar 18 10:37:50 duet3 DuetControlServer[1141]: [info] Settings loaded
Mar 18 10:37:51 duet3 DuetControlServer[1141]: [info] Environment initialized
Mar 18 10:37:51 duet3 DuetControlServer[1141]: [fatal] Could not connect to Duet (Invalid protocol version 6)
Now doing a
sudo apt-get update
sudo apt-get upgrade
Hi all,
So I'm finally getting around to adding the second extruder to my iDEX printer and I was wondering if someone knowledgeable would be kind enough to take a look at my config I've made? I'm waiting on a few connectors and tool so the printer isn't currently moving so I've take a guess on some of the offsets but some advice with that would also be appreciated but it's more the setup and naming of things I'm unsure of.
Edit to remove config files, as I'm making changes to my config. Will request help again soon 
Thanks in advance, James.
Start by watching these videos. https://youtube.com/c/ReneJurack
The first thing that stands out is you have defined multiple E factors in your config but you only have one Extruder, I think you meant to set multiple Z factors.
Ie
M350 X16 Y16 Z16 E16:16:16 I1 ; configure microstepping with interpolation
@emanuele same applies, select one and It will be further configured later, I would suggest leaving IO_0 free as this is used for a paneldue or serial communication.
Use the wiring diagram for pin names and function.
https://duet3d.dozuki.com/Wiki/Duet_3_Mainboard_6HC_Wiring_Diagram
@o_lampe Look into how the Prusa MMU2 does it, it's about forming a good tip to the filament.
@brian Uncomment T0 at the bottom.
And the bit referring to 3.3 is what firmware the config tool was set to when creating the config.g.