undefined
; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.15 on Sat Nov 26 2022 13:27:47 GMT+0100 (Mitteleuropäische Normalzeit)
; General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Proschi 3D E2" ; set printer name
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S1 ; enable Telnet
; Drives
M569 P0.0 S0 D3 H50 V30 ; physical drive 0.0 goes forwards
M915 P0.0 T50
M569 P0.1 S1 D3 H50 V30 ; physical drive 0.1 goes forwards
M915 P0.1 T30
M569 P0.2 S0 D3 H50 V30 ; physical drive 0.2 goes forwards
M915 P0.2 T50
M569 P0.3 S1 D3 H50 V30 ; physical drive 0.3 goes forwards
M915 P0.3 T50
M569 P0.4 S0 D3 H50 V30 ; physical drive 0.4 goes forwards
M915 P0.4 T50
M569 P0.5 S1 D3 H50 V30 ; physical drive 0.5 goes forwards
M915 P0.5 T50
M584 X0.0 Y0.1 Z0.2 E3:5 U4 ; set drive mapping
M350 X16 Y16 U16 Z16 E16:16 I1 ; configure microstepping without interpolation
M92 X80 Y80 U80 Z800 E286.216 :286.216 ; set steps per mm
M566 X480 Y300 U480 Z24 E300:300 ; set maximum instantaneous speed changes (mm/min)
M203 X12000 U12000 Y10000 Z600 E3000:3000 ; set maximum speeds (mm/min)
M201 X1000 U1000 Y500 Z100 E3000:3000 ; set accelerations (mm/s^2)
M906 X850 U850 Y850 Z800 E800:800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X10 Y-3 Z0 U35 S1 ; set axis minima
M208 X335 Y255 Z240 U355 S0 ; set axis maxima
; Endstops ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin null
M574 Y1 S1 P"io1.in"
M574 X1 S1 P"io2.in"
M574 U2 S1 P"Io4.in"
;M915 X S-63 H10 R1 ; Set very sensitive stall detect
;M574 X1 S3 ; configure endstop for stall detection
;M915 X S20 H140 R0 ; Set very sensitive stall detect
;M915 X S-63 H10 R1 ; Set very sensitive stall detect
; Filament Sensoren
M591 D1 P1 C"io5.in" S1
M591 D0 P1 C"io6.in" S1
; Z-Probe
M558 P1 C"io3.in" H5 A5 S0.005 F150 T6000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X10 Y20 Z0.5 ;0.55 Simplify set Z probe trigger value, offset and trigger height
M557 X30:330 Y50:210 P3 ; define mesh grid
; Heaters
M308 S0 P"Temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"Temp1" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T2 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S340 ; set temperature limit for heater 1 to 340C
M308 S2 P"Temp2" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 2 as thermistor on pin temp2
M950 H2 C"out2" T1 ; create nozzle heater output on out2 and map it to sensor 2
M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H2 S340 ; set temperature limit for heater 2 to 340C
; Temp Sensoren
M308 S10 Y"mcu-temp" A"MCU" ; defines sensor 10 as MCU temperature sensor
M308 S11 Y"drivers" A"Duet stepper drivers" ; defines sensor 11 as stepper driver temperature sensor
;M950 F5 C"out6" Q500 ; create fan 2 on pin fan2 and set its frequency
;M106 P5 H3 T40:70 ; set fan 2 value
; Fans
M950 F0 C"vfd" Q500 ; create fan 0 on pin out4 and set its frequency
M106 P0 C"Extruder&Bauteile" S0 H-1
;M950 F5 C"out6" Q500
;M106 P5 C"Board" S0 H-1
M950 F2 C"out3" Q500 ; create fan 0 on pin out4 and set its frequency
M106 P2 C"Filter Lüfter" S0 H-1 Q25000 ; set fan 0 value. Thermostatic control is turned off ; set fan 1 value. Thermostatic control is turned off
M950 F3 C"out5" Q500 ; create fan 2 on pin vfd and set its frequency
M106 P3 C"LED" S150 H-1 ; set fan 2 value. Thermostatic control is turned off
M950 F4 C"out4+out4.tach" Q25000
M106 P4 C"Aktiv Kühlung" S0 H-1
; Create a tool that uses the low end (X) carriage
M563 P0 D0 H1 F0 S"linker Extruder" ; tool 0 uses extruder 0, heater 1 and fan 0
G10 P0 X0 Y0 Z0 S0 R0 ; set tool 0 offsets and temperatures
; Create a tool that uses the high end (U) carriage
M563 P1 D1 H2 X3 F0 S"rechter Extruder" ; tool 1 uses extruder 1, heater 2, fan 2, and maps X to U
G10 P1 Y-0.4 U26.6 Z-0.10 R0 ; set tool 1 offsets and temperatures
; Create a tool that prints 2 copies of the object using both carriages
M563 P2 D0:1 H1:2 X0:3 F0:0 S"Duplicate"; tool 2 uses both extruders, hot end heaters and fans, and maps X to both X and U
G10 P2 X-25 Y0 U-176.3 Z0 S0 R0 ; set tool offsets and temperatures
G10 P2 R0 S0
M567 P2 E1:1 ; set mix ratio 100% on both extruders
;Create a tool that Prints in Mirrior Mode
M563 P3 S"Mirror" H1:2 D0:1 X0:3 F0:0
G10 P3 X-25 Y0 U-176.3 Z0 S0 R0
G10 P3 R0 S-2
; Custom settings are not defined
;Temperatur anpassung MCU
M912 P0 S2
; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss