Hi all!
So my SD card slot stopped working out of nowhere and I am in the process of putting in a replacement board.
I've upgraded the firmware from 3.1.1 -> 3.3 -> 3.4.6 and in all of these instances, I cannot get my WiFi access to work as every time I try to set my network details with M587, I get errors stating SPI Timout.
Here's my M587 command
>>> M587 S"Skynet" P"******"
SENDING:M587 S"SKYNET" P"*******"
Error: M587: Failed to add SSID to remembered list: SPI timeout
[ERROR] Error: M587: Failed to add SSID to remembered list: SPI timeout
Once this happens, I did try turning the WiFi module off and back on, but got the same result.
I've tried re-installing the firmware, but still the same SPI error.
I read on an old Git issue that sometimes M587 will not work the first time, but the second time it always does, and so I tried that, but after the first failed M587, the WiFi module turns off:
>>> M552 S0
SENDING:M552 S0
Error: WiFi module reported: no known networks found
[ERROR] Error: WiFi module reported: no known networks found
WiFi module is idle
>>> M552 S1
SENDING:M552 S1
Error: WiFi module reported: no known networks found
[ERROR] Error: WiFi module reported: no known networks found
>>> M587 S"Skynet" P"******"
SENDING:M587 S"SKYNET" P"*******"
Error: M587: Failed to add SSID to remembered list: SPI timeout
[ERROR] Error: M587: Failed to add SSID to remembered list: SPI timeout
>>> M587 S"Skynet" P"******"
SENDING:M587 S"SKYNET" P"*******"
Error: M587: Failed to add SSID to remembered list: WiFi module is disabled
[ERROR] Error: M587: Failed to add SSID to remembered list: WiFi module is disabled
I do see that 3.4.6 does not have a Duet2_SDIAP32_WiFiEth.bin, but 3.4.5 does and this is the one I used... Unsure if that's an issue?
And below is the output of M122, I do see that my WiFi version is 1.02 - is that the most recent?
Output of M122
>>> M122
SENDING:M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.6 (2023-07-21 14:08:28) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S8-6JKD4-3SJ6T-9A46J
Used output buffers: 1 of 26 (3 max)
=== RTOS ===
Static ram: 23896
Dynamic ram: 75924 of which 0 recycled
Never used RAM 9404, free system stack 193 words
Tasks: NETWORK(ready,7.5%,336) HEAT(notifyWait,0.0%,353) Move(notifyWait,0.0%,363) MAIN(running,90.8%,456) IDLE(ready,1.7%,30), total 100.0%
Owned mutexes: USB(MAIN)
=== Platform ===
Last reset 00:00:54 ago, cause: power up
Last software reset details not available
Error status: 0x00
[ERROR] Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 27.9, current 30.4, max 30.7
Supply voltage: min 1.4, current 1.8, max 1.8, under voltage events: 0, over voltage events: 0, power good: no
Heap OK, handles allocated/used 99/26, heap memory allocated/used/recyclable 2048/374/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: ok, SG min n/a
Driver 1: ok, SG min n/a
Driver 2: ok, SG min n/a
Driver 3: ok, SG min n/a
Driver 4: ok, SG min n/a
Driver 5:
Driver 6:
Driver 7:
Driver 8:
Driver 9:
Driver 10:
Driver 11:
Date/time: 1970-01-01 00:00:00
Cache data hit count 2329443531
Slowest loop: 4.28ms; fastest: 0.13ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is ready with "M122" in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 1.34ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 0 of 8
= WiFi =
Interface state: active
Module is idle
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address e0:98:06:23:00:47
WiFi Vcc 3.47, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 27448
Clock register ffffffff
Socket states: 0 0 0 0 0 0 0 0
Keen to see if I missed a step or updated the firmware in the incorrect order and if someone knows how I can get out of this SPI Timeout error?
Thanks for reading!
Tim
