Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. Zseven
    3. Posts
    • Profile
    • Following 2
    • Followers 0
    • Topics 13
    • Posts 41
    • Best 2
    • Controversial 0
    • Groups 0

    Posts made by Zseven

    • 6hc as expansion

      Hello everyone,
      is there a guide on how to use the Duet 6HC as an expansion board with the 6XD, and how can I configure it?

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: 24 volt fan with PWM control

      @oliof

      Hello ,
      here is my solution for the 6XD board

      17-06-2024_20-03-42.jpg

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: 24 volt fan with PWM control

      @oliof

      I have fix it !

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: 24 volt fan with PWM control

      @oliof

      ello ,
      I have now got a replacement as the last fan has burnt out.

      08-06-2024_08-37-38.jpg

      DC7-24V brushless turbo fan motor 100000 rpm high speed aluminium alloy impeller with brushless motor and speed controller

      I have now connected the fan direnkt to the 24V power supply and I can control it very well with the potentiometer

      I have now measured the voltage at the potentiometer and between the red and black cable are 5V

      The yellow cable should be the PWM signal.

      How can I now control this fan with the Duet 6xd?

      Witch pins ?

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: 24 volt fan with PWM control

      @oliof

      Hello ,
      I have requested the data sheet from the manufacturer.

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: 24 volt fan with PWM control

      @oliof

      Yes !

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: 24 volt fan with PWM control

      @Phaedrux

      Hello ,
      I have
      +24V at Out5 / V_OutLC1
      -Out 5 / GND
      PWM at Out 5 / out5-

      in config.g

      M950 F2 C‘!out5’ Q1000
      M106 P2 S0.0 H-1 C ‘Blower’

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: 24 volt fan with PWM control

      @Phaedrux

      I have connected the fan and set the parameter Q1000. If I set the speed in the DWC to 95%, the motor burns out!

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: 24 volt fan with PWM control

      @Phaedrux Yes, I have read it but not understood it.
      The fan has 3 pins 1x +24v 1x - 1x pwm

      Which is the pwm output?
      Outx-
      Or outx.tach

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: 24 volt fan with PWM control

      @Phaedrux
      Which pins can I use?

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • 24 volt fan with PWM control

      Hello, I have a question about the wiring of a fan.
      I have a 24 volt fan with PWM control.

      My motherboard is a 6XD.

      Can anyone help me?

      ![IMG_0529.jpeg](/assets/uploads/files/1717084212deee41b7e84888f7fc58090366cf.mp4 9702675-img_0529.jpeg) IMG_0530.jpeg

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: duetpi will not run on usb ssd - raspbian will

      @chrishamm Hello, have you solved the problem? That you can boot from ssd despite automount ?

      posted in Firmware installation
      Zsevenundefined
      Zseven
    • RE: Multiple Analog ZProbe

      @Phaedrux

      Thank You it Works.

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: Multiple Analog ZProbe

      @Phaedrux

      Yes i Use 6XD.

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: Multiple Analog ZProbe

      @Phaedrux

      Hello ,

      yes, I have installed a load cell in each tool which outputs an analog value.

      The background is that I want to measure the tool offset and the filament pressure on the nozzle.

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: Multiple Analog ZProbe

      @oliof
      3 Tool whit analoge z-probe (Pessure Sensor)

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: Multiple Analog ZProbe

      @Phaedrux

      Hello ,

      I have the Duet 3 6XD

      I found this in the documentation:
      From RRF 3.1.0, you can define multiple probes.

      The K parameter in M558 selects the Z probe number. If there is no K parameter then 0 is used. You can ignore this parameter if you have only one Z probe.
      Z probe #0 can use probe types 0, 1, 2, 3, 5, 8, 9 or 10. All other probes must be probe type 0, 8, 9 or 10.
      

      But why is that so ?
      I need 3x type 2

      Translated with DeepL.com (free version)

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • Multiple Analog ZProbe

      IMG_6515.JPEG Hello
      why can I only set 1x analogue sample?
      Why are not more supported?

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • RE: define an analog input?

      @o_lampe
      Hello ,

      but is that basically possible ?

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven
    • define an analog input?

      Hello ,

      I have a question. How can I define an analog input? For example, it should switch when 3.2 volts are reached?

      Is there a solution ?

      posted in Duet Hardware and wiring
      Zsevenundefined
      Zseven