Announcement: Duet 3 Toolboard revision v1.1

Ariana

Hey Guys,
Hope you are doing well.
Any chances that I can get the schematic and PCB of the new Version?
Thank you in advance.

KipK

So I need a Toolboard to finish a current build now. Which reseller in EU is supposed to receive 1.1 stock shortly?

fotomas

@kipk
I have reserved one at
https://www.dold-mechatronik.de/

They expect it to be in stock next week.

KipK

@fotomas thanks for the tip

martin7404

@pixelpieper looks great , but what about the orientation of the accelerometer?

zapta

@t3p3tony said in Announcement: Duet 3 Toolboard revision v1.1:

@lbi we looked at that but, as you can see, there is not a lot of space left!

Every board has two sides.

T3P3Tony

@zapta true. in this case we need to keep the board manufacturable at a reasonable cost and also thin enough to fit on a hermera tool on a toolchanger

pixelpieper

@martin7404 its a 3d-accelerometer, you can adjust the orientation in software.

zapta

@t3p3tony said in Announcement: Duet 3 Toolboard revision v1.1:

@zapta true. in this case we need to keep the board manufacturable at a reasonable cost

@t3p3tony, that's correct, good engineering is about striking the right balance.

BTW, I appreciate the density of your designs. I presume this one is also with Kicad. I played with much simpler design and know how much effort it takes.

A Former User

@t3p3tony

A small wish (and with please ) :

In the next iteration, maybe already the next board-run(?), please consider reviewing if you can add in also the through-hole-solderpads for the stepper-motor-out
(guess I am one of the few that are no "crimp-ist", push-in would be favourite, otherwise will stick to screw-in-terminals )

Best regards

dc42

Push in is very nice, but expensive compared to crimp connectors, and quite large - I haven't seen any with less than 2.5mm pitch and they tend to be quite high.

A Former User

@dc42 said in Announcement: Duet 3 Toolboard revision v1.1:

Push in is very nice, but expensive compared to crimp connectors, and quite large - I haven't seen any with less than 2.5mm pitch and they tend to be quite high.

Thanks so much for answering! Yep most I found in some webshops were too expensive/big/... for now, but I just wanna try something other then crimping, maybe I stick with solder-in-screwin-terminals in the end... Guess I am on some sort of a quest there if you provide me the 4 additional motor-throughhole-solderpads, I will see what I get and will post it in the forum I guess my talent for crimping is just not really there

dc42

@lbi do you have a proper crimp tool?

I hate crimping, but once done it makes disconnecting and reconnecting wires much quicker than using screw terminals.

fotomas

Are there any parts for crimping bundled with the toolboard (like duetboard)?

T3P3Tony

@fotomas yes there is a connector pack with the board

martin7404

@fotomas I did received mine from dold
And it working great.
For now I tested only accelerometer as far I am building new large 3d printer. It took 15 minutes to crimp wiring, solder the 120 ohm bridge and run.

A Former User

@dc42 said in Announcement: Duet 3 Toolboard revision v1.1:

@lbi do you have a proper crimp tool?

I hate crimping, but once done it makes disconnecting and reconnecting wires much quicker than using screw terminals.

At least I am not alone in the universe with that issue yeah of course you have a point, I know I can force myself to do it, just the outcome is appropriate to my feeling while doing it, I can borrow a tool at work, but some of them work even better when "crimped" by hand with a tiny plier... Ah for now I crimp, it is alright. Just would be great in the future to have the possiblity maybe to even order them with no connnectors soldered and buy either a screw-in or a crimp-connector kit and just solder it there, and for that the 4 through-hole-pads for the motor are missing. I know this would be / is for advanced users... but my solder-skills are actually not as bad as my crimp-skills are. Didn´t want to bother all of you. It is allright. Keep up your work!

Best regards

DIY-O-Sphere

@T3P3Tony
Is there a rough estimate when the product will be available again in germany ?

dc42

@diy-o-sphere there is another batch currently undergoing testing, so I don't think it will be long.

khenderick

Nice work, great to see that you listen to customer feedback.

Some feedback/questions from my end:

I do like the crimped connectors, but nice to see that the holes are still there for people preferring screw terminals. A suggestion for a future revision would be to align these holes so that one solid row of screw terminals can be mounted instead of separate sets. This makes the terminals a lot more sturdy and one would be less likely to damage pads or connectors if using too much force fastening the wires.
As a v1.0 owner, I'm a tad sad to see I'm missing out on all the accelerator fun.
Therefore the question whether I (being familiar with patching hardware, soldering and epoxy) would somehow be able to retro-fit an accelerometer to the v1.0 hardware. I was thinking about some daughter board holding the accelerometer and some passives and then connecting it to some pads/traces.
- If possible, any docs on what to do, or schematics to look at?
- In either case, it might be a good idea for a future revision to break out every (unused) signal/pin to testpoints so patch boards can be made.