Issues with pressure advance since RRF 3.4

jay_s_uk

I've printed test files with 3.2.2, 3.3 and 3.4.4 and have no been able to see a difference

oliof

@dc42 thanks for the additional insight! It may also be a bit slicer dependent. I remember KISS Slicer for example is doing a slight inwards bend before steep angles; other slicers may not do this.

Argo

I already tested different slicers and settings also different RRF versions.

Only thing that helped with my machine was connecting Klipper (Pi).
I suspect that PA smooth time is the factor (feature) that is RRF missing to improve this.

But the reasons why my bedslinger (also RRF with Duet 3 Mini) produces better corners? I don't know. My Voron (printer with the issues) uses a different kind of hotend which is also not compatible with the PID algorithm RRF uses as PID tuning only works when calibrating the hotend as heater and not as a tool But that's another issue I already reported in another thread.

gnydick

I can conclusively report that Input Shaping interferes with Pressure Advance. Didn't know if anyone else has been able to confirm on their prints.

evan38109

@gnydick I've also seen issues with input shaping + pressure advance, though I'm always open to having done something wrong on my end. At the risk of hijacking a closely-related-but-not-quite-the-same thread, you can see the artifact show up as an indentation before and after turns in the photo below. I wasn't able to remove it with any amount of tuning.

gcode here.
Ringing tower model here.
Config files for the machine when the above was printed in this commit. (Newer repo state is a bit different; I'm converting to closed loop.)
If you want to re-slice for your machine, the PrusaSlicer layer change script, designed for 0.25mm layer height, is:

{if layer_num== 1}
M593 P"none"                           ; no input shaping
M572 D0 S0                             ; no PA
{elsif layer_num== 60}
M593 P"ei3" F42 S0.1                   ; enable input shaping
M572 D0 S0                             ; no PA
{elsif layer_num== 120}
M593 P"none"                           ; no input shaping
M572 D0 S0.09                          ; enable PA
{elsif layer_num== 180}
M593 P"ei3" F42 0.1                    ; enable input shaping
M572 D0 S0.09                          ; enable PA
{endif}

droftarts

@gnydick said in Issues with pressure advance since RRF 3.4:

I can conclusively report that Input Shaping interferes with Pressure Advance. Didn't know if anyone else has been able to confirm on their prints.

… which is why we recommend tuning pressure advance AFTER tuning input shaping.

Ian

evan38109

@droftarts Yes, I've heard this before and followed this instruction.

First, I tuned IS with PA off, arriving at M593 P"ei3" F42.

Second, I printed this calibration print with input shaping held constant and PA values varied from 0.00 at the far right (bottom of the print) to 0.14 at the far left, incrementing every 5mm.

Note how the pre- and post-seam artifact is not present when PA is zero on the right-hand side when PA is off. The artifact I am referring to the horizontal line / thin section that measures around 4mm before and after the seam, and the corners. It's present for any PA values from way too low to way too high as long as IS is enabled, and absent if PA is off. Apologies for my photography.

Did I misunderstand something? What else could I have done?

gnydick

@droftarts, makes no difference.

Monteaup

I had this issue for nearly two years... No problem with marlin firmware.

Tried everything. Changed Steppers, different extruders, hotends, bowden tubes.... I had to use a PA value of 0.4 with a 5cm bowden.

New Year, new (last) try. Had already a bambu lab printer in the basket. Instead, I ordered an Malow NF Sunrise extruder. Thought, this has to work. It's a all in one solution.

First print yesterday without calibration a PA value of 0.04 with perfect corners.

Argo

@Monteaup

It seems some extruder / hotends cause issues with the PA implemenation we have atm with RRF.
With Klipper you also would need to play around with "PA smooth time" so PA does work properly. Maybe we'll see such implementation in RRF anytime soon.

dc42

@Monteaup, you show two cubes in your photo. What is the difference in print settings between the two?

Can you post a more detailed close up photo of the seam that you say is present for any PA values?

PA doesn't fully address the problem of over-extrusion in corners. I am looking to address this separately.

CCS86

@evan38109 said in Issues with pressure advance since RRF 3.4:

@droftarts Yes, I've heard this before and followed this instruction.

First, I tuned IS with PA off, arriving at M593 P"ei3" F42.

Second, I printed this calibration print with input shaping held constant and PA values varied from 0.00 at the far right (bottom of the print) to 0.14 at the far left, incrementing every 5mm.

Note how the pre- and post-seam artifact is not present when PA is zero on the right-hand side when PA is off. The artifact I am referring to the horizontal line / thin section that measures around 4mm before and after the seam, and the corners. It's present for any PA values from way too low to way too high as long as IS is enabled, and absent if PA is off. Apologies for my photography.

Did I misunderstand something? What else could I have done?

This is a great photo and example of some strange interaction between PA and IS. Something isn't right.

evan38109

@CCS86 I mean...maybe? If I'm betting on something being wrong, I bet it's me, not RRF.

Have you seen the same thing? It should be easy to recreate, just print a one-wall cube with the seam on the side while both IS and PA are enabled vs. not enabled. Make sure to disable any kind of dynamic speed control in the slicer. (e.g., "Slow down if layer print time is below...")

camnewnham

@dc42 said in Issues with pressure advance since RRF 3.4:

@Heartleander81 said in Issues with pressure advance since RRF 3.4:

@R4ffers oh yes.
@dc42 is there also something like pressure advance smooth time under RRF? A few clippers have the problem with the high smooth time, but those who have problems are mostly DirectDrive extruder users. Maybe that's an approach you can follow.

No, there isn't anything similar. I will look into that Klipper feature.

Hi @dc42, just wanted to +1 this feature.

I run a delta / duet WiFi with a ~400mm bowden and 0.325 pressure advance, with input shaping. The print quality is excellent.

However, when I turn up the print speed/acceleration, I also need to increase extruder jerk - as expected with pressure advance. EXYZ all cope fine - no skipped steps or filament stripping - however on short zig-zag movements it tends to jerk rapidly back and forth which creates some noise (and the extruder is/was fixed to the frame).

As a result, I have switched to a suspended/lying extruder so that I can turn pressure advance down and maintain higher print speed but I see this as a temporary solution.

If smooth pressure advance is anything like the graphs here it looks like it might help to resolve this issue

Do you think it would have any benefits for this scenario?

ctilley79

@Argo @dc42 I know this is an old thread, but was the following change in 3.5b3 designed to fix this very issue?

"When input shaping is used, extruder motion is now synchronised to the shaped axis motion"

Argo

@ctilley79

I'd say it's a 80% improvement to before and compared to my printers with Klipper or Bambu X1.
So it was definitely a step in the right direction.

A Former User

Sorry for bumping such an old thread, but I think I am having similar issues. No matter what my PA setting is, I am getting buldging corners. Also @gnydick said "Right now, with even just a low poly curved surface, each segment is ~1.5mm long, I get a bulge at every direction change." This is something I, and some others have found to be a problem in this thread.https://forum.duet3d.com/topic/33692/input-shaper-causing-stutters-and-blobs-on-curves-rrf3-5-0-rc-1

Is PA smoothing something that may be impelmented any time soon? Is there any other fix for this?

I'm considering moving over to Klipper to see if I can solve some of the issues I'm having, but I really wish I didn't have to since I'm generally really happy with RRF on my Duet 3 Mini.

Notepad

Just chiming in for visibility as I can also confirm to be noticing what appears to be PA oddities in regards to corner bulging, but also material deposition before and after a corner.
The hardware I use is a HemeraXS with a CHT 0.6mm Volcano nozzle with a InputShaper of EI2@20hz or EI2@48hz. Pictured is PA0.035

The issue is more noticeable with a 0.6 nozzle compared to the 0.4.
I need to use a PA value of 0.045 to get non bulged corners, however by doing so I get inconsistent extrusion before and after the corner.

There appears to be a correlation with flow rate and the severity of the behaviour. When pushing flow rates (>35mm^3/s) close to the limits of the nozzle, the behaviour is at its worst. which makes sense as the pressure differential would be the greatest. What is puzzling is that the issue also appears in smaller parts where the flow rates are below 60% of the nozzle capacity.

I am currently using PA of 0.025 which is a middle ground of bulged corners and under/over extrusion.

I have not currently found any changes in this behaviour by changing the Input Shaper frequency nor shaper type
For extruder settings I was running a jerk value of 4mm/s (250mm/min) and an acceleration of 66mm/s2 (4000mm/min) - I am currently testing higher jerk and acceleration settings however data has been inconclusive so far

A Former User

@dc42 I don't mean to be a nag, but is there any chance PA smoothing (or similar) will be added to RRF in the near future?

I've been trying to tune out corner bulging for days, changing just about everything I can and even buying a new nozzle, but I'm still not able to get a PA value that can remove the bulging without causing other extrusion problems in corners.

PA change bulging.jpg

ctilley79

@Threepwood

Something mechanical is going on here. PA works great for me on RRF. your issues are something else entirely.