6XD I/O >> Issue solved

droftarts

@tecno Ah, that looks like an RGBW ring. Try

M950 E0 C"led" Q3000000 T2
M150 E0 R255 P128 S20 F0

M950 T2 tells RRF that it's RGBW, not RGB.

Ian

tecno

@droftarts

Same same

Will change LED ring to one with black PCB board. This a job for torrow

tecno

@droftarts

Morning Ian,

Changed LED strip and only 1 of 8 is working on this one too.

M950 E0 C"led" Q3000000 T2
M150 E0 R255 P128 S20 F0

Any suggestions?

Cheers
Bengt

droftarts

@tecno I've just tested both RGB and RGBW LEDs on my 6HC, both worked without issue. I've asked someone with a 6XD to test.

Can you post a link to the white LED ring you bought? And post a picture of the current wiring?

Ian

tecno

@droftarts

https://vi.aliexpress.com/item/1005002313192735.html?spm=a2g0o.order_list.order_list_main.11.364b1802NFG3VP&gatewayAdapt=glo2vnm

Both white and ´blach PCB 8 LEDS

Wiring https://forum.duet3d.com/post/345489

gloomyandy

@tecno Shouldn't the control signal be going to d0 and not to d1?

tecno

@gloomyandy

As I understand is 6XD D0 out goes to Di in.

droftarts

@tecno Those do look like RGB LEDs, looking closer. Though they should light up, just with the wrong colours, if you put the wrong T parameter in M950.

I thought you said you had changed the wire over? @tecno said in 6XD I/O >> Issue solved:

Change White to shield.

On each LED, there is a corner 'notch' to indicate which pin is GND. Can you check continuity of GND, DI and 5V from the LED pins to the connector?

@gloomyandy It's DI for Digital In, DO is Digital Out, where it passes the signal on to the next one. Mine are labelled and wired like that.

Ian

gloomyandy

@tecno This has nothing to do with the 6XD I'm talking about the pads on the LED ring, there is a D0 and a D1. Your wiring here: https://forum.duet3d.com/post/345489 shows it going to D1 I think it should go to D0. It seems very odd to me to have the input labelled D1 and the output labelled D0.

gloomyandy

Ah yes that may be Din and Dout I suppose. Oh well good luck!

tecno

@droftarts
So now I changed White to signal and Shield is now 5V

So now we are getting closer

droftarts

@tecno Okay, so now use:

M950 E0 C"led" Q3000000 T1

ie change T2 to T1

I expect that bare 'earth' wire had too much capacitance to transmit the signal. Now you're using the bare wire for 5V, so easier to create a short. Same goes for using that wire for GND. I'd replace the wiring with individually insulated wires, ie 3-core wire. If you don't have 3-core wire, use left-over stepper motor wire, that's about the right gauge for LEDs.

Ian

tecno

@droftarts

Works in R255 and P can be set = Nice.

Now to play with new colors

droftarts

@tecno Do all 8 LEDs work now, and are controllable?

RGB LEDs aren't the best for white light. You'll have to play around with the levels in M150 for R, U (for green) and B, and brightness (P) to get close to what you want. If it's mostly white you want, you probably should have got RGBW, or just white, LEDs.

Ian

tecno

@droftarts
Yes all 8 work

I am aware that I can not get perfect greyscale with RGB. Hard to find 8leds RGBW that fits.

Thank you very much for your kind help Ian, I owe you a pint or two

I am sure more questions will arise

Cheers
Bengt

tecno

tecno

@droftarts

@tecno said in 6XD I/O >> Issue solved:

;***Outputs
M950 P0 C"out0" ; Q500 ;#1 Nozzle Vacuum
M950 P1 C"out1" ; Q500 ;#2 Nozzle Vacuum
M950 P2 C"out2" ; Q500 ;Drag PIN Actuator
M950 P3 C"out3" ; Q500 ;ENA Nozzle 1/2 Up
M950 P4 C"out4" ; Q500 ;Xross cursor
M950 P5 C"out5" ; Q500 ;LED light x
M950 P6 C"out6" ; Q500 ;Vacuum power

Have problem with Outputs 4 and 5. can not switch off. Any advice is appreciated-

Off=1.4V On=1.3V all other Off 24V On 0V

tecno

@droftarts

Is this something we can get working?

There is a cable with RX/TX/GND for the old controller. Two chips for vacuum measurement.

Cheers
Bengt

droftarts

@tecno said in 6XD I/O >> Issue solved:

Have problem with Outputs 4 and 5. can not switch off. Any advice is appreciated-
Off=1.4V On=1.3V all other Off 24V On 0V

Was this working before? Have you fixed it? Sounds more like a wiring problem.

Is this something we can get working?
There is a cable with RX/TX/GND for the old controller. Two chips for vacuum measurement.

What chip is it? You need to find out what signal it outputs, and what signal it expects. If it outputs an analog signal of 0-3.3V, you can probably set it up as an analogue sensor, or a digital sensor if it outputs an on/off signal.

Ian

tecno

@droftarts
Hello Ian,

These two worked OK with original controller, never got them working with 6XD.
Wires have been checked, but I have to measure continiuity once moore on out 4 and 5.

Have to dismanlte the board and see what is on it.

Bengt