Duet 3 : No tool nor bed shown

engikeneer

@Donpi double check your firmware version. Send M115 in the console to see what it says. You should be running version 3.1.1 to match your config.

droftarts

@Donpi I can't see anything particularly wrong with your config.g. Please send M122 and post the reply. Are you using Duet 3 in standalone or with SBC?

Also, send M98 P"config.g" and see if config.g generates any errors. If not, send M308 S0 and M308 S1 to report sensor configuration, then M950 T0 and M950 T1. You should get a response something like:

M308 S0
Sensor 0 type Thermistor using pin bedtemp, reading 19.1, last error: sensor not ready, T:100000.0 B:3988.0 C:0.00e+0 R:4700.0 L:0 H:0
M950 H0
Heater 0 pin bedheat frequency 250Hz, sensor 0

Ian

Donpi

@engikeneer M115 return this :

jay_s_uk

@Donpi I would upgrade your firmware to 3.1.1 first.
https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware
https://github.com/Duet3D/RepRapFirmware/releases/tag/3.1.1

Donpi

@droftarts

I use a Raspberry 4 2Go as SBC.

M98 P"config.g" Show me the welcome message again.
But no error

Here is the return of
M308 S0
M308 S1
M950 S0
M950 S1

M122 returns this :

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.01-RC9 running on Duet 3 MB6HC v1.01 or later
Board ID: 08DJM-956BA-NA3TN-6JTDG-3SD6J-TABLTUsed output buffers: 1 of 40 (11 max)
=== RTOS ===
Static ram: 154572
Dynamic ram: 160680 of which 20 recycled
Exception stack ram used: 264
Never used ram: 77680
Tasks: NETWORK(ready,2076) HEAT(blocked,1412) CanReceiv(suspended,3824) CanSender(suspended,1484) CanClock(blocked,1432) TMC(blocked,216) MAIN(running,5036) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 00:03:46 ago, cause: power up
Last software reset details not available
Error status: 0
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 20.8, current 26.6, max 26.8
Supply voltage: min 24.9, current 24.9, max 25.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
Driver 0: standstill, reads 6924, writes 11 timeouts 0, SG min/max 0/0
Driver 1: standstill, reads 6925, writes 11 timeouts 0, SG min/max 0/0
Driver 2: standstill, reads 6925, writes 11 timeouts 0, SG min/max 0/0
Driver 3: standstill, reads 6926, writes 11 timeouts 0, SG min/max 0/0
Driver 4: standstill, reads 6926, writes 11 timeouts 0, SG min/max 0/0
Driver 5: standstill, reads 6927, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2020-11-18 12:04:16
Slowest loop: 3.26ms; fastest: 0.14ms
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0 0, running macro
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 1.90ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8
- Ethernet -
State: disabled
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 0, longest wait 0ms for type 0
=== Linux interface ===
State: 0, failed transfers: 0
Last transfer: 17ms ago
RX/TX seq numbers: 6649/6650
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.1.1
Daemon:
Finishing macro daemon.g, started by system
> Next stack level
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 0.82

Donpi

@jay_s_uk
you meen with with
sudo apt update
sudo apt upgrade

I'll allready done it but noting install.

A Former User

@Donpi said in Duet 3 : No tool nor bed shown:

I'll allready done it but noting install.

try running M997 the previous post shows the software on the pi is 3.1.1. M997 should try to flash the board to match.

Donpi

@bearer @jay_s_uk @engikeneer
The M997 worked... I guess
now M115 reutrns :

But still nothing...

Veti

@Donpi said in Duet 3 : No tool nor bed shown:

M950 S0
M950 S1

you wrote T instead of S

Donpi

@Veti Yeah, in this case, even S was wrong

M950 H0 and H1 give the same response :
Heater 0 does not exist

Veti

@Donpi said in Duet 3 : No tool nor bed shown:

M350 X16 Y16 Z16:16 E16 I1 ; Configure microstepping with interpolation

you are not allowed to specify 2 z values.

what i would suggest is. save all your config files and generate an new one from the configurator.
then slowly start adding your additional configs one by one until it breaks.

droftarts

@Donpi My mistake, send M950 H0 and M950 H1 (not T0/1) to check heater definition. Also send M563 P0 to check tool definition.

M563 P0
Tool 0 - name: T0; drives: 0; heaters (active/standby temps): 1 (0.0/0.0); xmap: X; ymap: Y; fans: 0; status: selected

But M308 S0 and S1 reporting "Sensor does not exist" does seem to imply there is a problem with your M308 definition in config.g. What happens if you send M308 S0 P"temp0" Y"thermistor" A"Bed Temp" T100000 B4700 C0.0000000706?

Ian

Donpi

@droftarts strange this work well.
and if I call M308 S0, it says :
Sensor 0 (bed Temp) type bla bla bla...

It's like my config.g is not readed or somthing reset everything

Donpi

@Veti With a complettely new copnfiguration strait from the generator I have the same behaviour

Veti

what version of the duet web control are you running?

Donpi

@Veti
I'am a bit puzzled ...

I have created a macro with my config.g.
And running the macro I get the tootls and heaters...
It' just give me this errors

I don't know why my config.g is ignored...

Donpi

@Veti My duet web control is 3.1.1

Donpi

Hum the macro is not saved in the micro SD ... I think the problem is from here ...

droftarts

@Donpi If you're using SBC, you shouldn't have an SD card in the Duet! The O: directory is a virtual SD drive on the Raspberry Pi. See https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_Virtual_SD_card

Where is your config.g? On the SD card in the Duet, or on the Raspberry Pi?

Ian

Donpi

@droftarts
Of cours in the raspberry
There is no card on de Duet