Posts made by tracar

@Phaedrux i will try to recreate the situation after the print is done, , if it spikes i can verify with a thermal probe too.... post my findings later

@Phaedrux said in Connection issue on long prints.:

y weird. It could be interference on your thermistor wiring, or a bad connection.

that is the only time the heater did that,, directly after m112, while it was sitting there with the trying to reconnect popup. and as you can see i entered m112 twice,,, just as the heat graph shows, then the time where it dropped off in temp as i hit the reconnect button,,,

kinda what i was thinking, after everything else can just not the pc...

did you notice the heaters did that little thing off the scale ?

@tracar said in Connection issue on long prints.:

dont see the fix. after many hours the webpage dro

M122 after the connection problem...
m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2 running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N8PS4-7J9D4-3S86R-KAA3N
Used output buffers: 3 of 24 (21 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73860 of which 80 recycled
Never used RAM 14680, free system stack 103 words
Tasks: NETWORK(ready,180) HEAT(blocked,309) MAIN(running,402) IDLE(ready,19)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 13:58:41 ago, cause: software
Last software reset at 2021-01-15 20:44, reason: User, GCodes spinning, available RAM 14924, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 25.7, current 27.7, max 28.8
Supply voltage: min 23.8, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 86402, standstill, SG min/max not available
Driver 1: position -17072, standstill, SG min/max not available
Driver 2: position 17952, standstill, SG min/max not available
Driver 3: position 0, ok, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-01-16 10:43:32
Cache data hit count 4294967295
Slowest loop: 69.13ms; fastest: 0.18ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 5.0ms, write time 2.1ms, max retries 0
=== Move ===
DMs created 83, maxWait 194553ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 536861, completed moves 536855, hiccups 2, stepErrors 0, LaErrors 0, Underruns [118, 0, 0], CDDA state 3
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.3
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 X228.584 Y264.573 E0.7917" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 201.81ms; fastest: 0.10ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 1
  WiFi firmware version 1.25
  WiFi MAC address ec:fa:bc:5b:3f:ab
  WiFi Vcc 3.43, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 22208
  WiFi IP address 192.168.0.111
  WiFi signal strength -72dBm, mode 802.11n, reconnections 0, sleep mode modem
  Clock register 00002002
  Socket states: 0 0 0 0 0 0 0 0
  1/16/2021, 10:41:18 AM Connected to 192.168.0.111

++++++++++++++++

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Aug 30 2020 09:00:14 GMT-0600 (Mountain Daylight Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Duet2" ; set printer name
M669 K1 ; select CoreXY mode

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Input/Output Physical Estop
M950 J1 C"e1stop" ; e1_stop pin on the mainboard
M581 P1 T0 C0 S0 ; T0 = emergency stop on trigger

; Drives
M569 P5 S1 T5 R1 ; physical drive x goes forwards
M569 P6 S1 T5 R1 ; physical drive y goes forwards
M569 P7 S1 T5 R1 ; physical drive z goes forwards
M569 P8 S1 T5 R1 ; physical drive U goes forwards
M569 P3 S1 ; physical drive extruder goes forwards
M584 X6 Y5 Z7:8 E3 ; set drive mapping
M671 X-50:490 Y330:330 S5 ; x leadscrew position left to right from o,o on y axis , S5 means can adjust up to 5 mm
M350 X16 Y16 Z16 E16 I1 ; configure micro stepping with interpolation
M92 X200.5 Y200.5 Z800.00 E93 ; set steps per mm

; FEEDRATE CONVERSIONS
; 1.6mm/s = F100
; 10mm/s = F600
; 16mm/s = F1000
; 20mm/s = F1200
; 35mm/s = F2100
; 50mm/s = F3000
; 70mm/s = F4200
; 100mm/s = F6000
; 120mm/s = F7200
; 133mm/s = F8000
; 160mm/s = F10000
; 250mm/s = F15000

M566 X1200 Y1200 Z1200 E3000 ; jerk settings testing
;M566 X250.00 Y250.00 Z5.00 E120.00 ; set maximum instantaneous speed changes (mm/min) (original jerk settings)
M203 X8000.00 Y8000.00 Z1000.00 E4000.00 ; set maximum speeds (mm/min)
M201 X200.00 Y200.00 Z15.00 E400.00 ; set accelerations (mm/s^2)
M906 X300 Y300 Z300 E1800 I30 ; set motor currents (mA)
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X440 Y528 Z895 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure active-low endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop" ; configure active-low endstop for high end on Y via pin ystop
M574 Z1 S1 P"zstop+e0stop" ; configure active-high endstops for low end on Z via pins zstop and e0stop

; Z-Probe
M950 S0 C"!exp.heater7" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T24000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-.04 Y-26.5 Z3.44 ; set Z probe trigger value, offset and trigger height ( the higher the number the smaller the spacing )
;uncomment one probe grid you want below
M557 X20:430 S205 Y80:535 S212.5 ; define mesh grid With 9 points mapped
;M557 X20:430 S102.5 Y80:535 S106.25 ; define mesh grid With 25 points mapped

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 A138.4 C562.2 D0.8 S1.00 V120.0 B0 ; disable bang-bang mode for Bed and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 A385.4 C119.0 D3.5 S1.00 V24.2 B0 ; disable bang-bang mode for heater and set PWM limit

; Fans

M950 F0 C"fan0" Q500 ; create fan0 on pin fan0 and set its frequency
M106 P0 C"part/bridging fan" P1 S0 H-1 ; set fan0 "H-1 disables thermostatic mode" or H1 enables. ("S" parameter turns that fan on or off S0 or S1) (T45 is fan on at 45 degrees)

M950 F1 C"fan1" Q500 ; create (Tool fan 1) on pin fan1 and set its frequency
M106 P1 C"Hot end fan" S0 H1 T45 ; set (Tool fan 1) value. Thermostatic control is turned off

M950 F2 C"e1heat" Q20000 ; create fan on pin e1heat and set its frequency ( connected to Solid State relay )
M106 P2 C"Neopixels ON/OFF" S1 H-1 ;set fan 2 name and value. Thermostatic control is turned off

M950 F3 C"fan2" Q20000 ; create fan2 on pin fan0 and set its frequency ( connected to Solid State relay )
M106 P3 C"Relay 2 ON/OFF" S0 H-1

; Tools
M563 P0 S"Flexion" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
M501

---

yes you are correct, the pc will not connect without a restart.

but tablet and cell will , in both local wifi and or cellular only..

i typed m112 instead, Twice,, noob..... anyways look at the temp during the seconds i did not hit the reconect button........... Hmmmmmm

m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2 running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N8PS4-7J9D4-3S86R-KAA3N
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73652 of which 44 recycled
Never used RAM 14924, free system stack 191 words
Tasks: NETWORK(ready,180) HEAT(blocked,309) MAIN(running,470) IDLE(ready,19)
Owned mutexes:
=== Platform ===
Last reset 00:00:27 ago, cause: software
Last software reset at 2021-01-15 20:44, reason: User, GCodes spinning, available RAM 14924, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 26.0, current 26.7, max 27.2
Supply voltage: min 24.0, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-01-15 20:45:18
Cache data hit count 33439127
Slowest loop: 8.21ms; fastest: 0.23ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.8ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.76ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.25
  WiFi MAC address ec:fa:bc:5b:3f:ab
  WiFi Vcc 3.43, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 25360
  WiFi IP address 192.168.0.111
  WiFi signal strength -69dBm, mode 802.11n, reconnections 0, sleep mode modem
  Clock register 00002002
  Socket states: 4 0 0 0 0 0 0 0

im starting another 30 hour print i will repost another M122 after its doneto compare.

its been said here lots, and i dont see the fix. after many hours the webpage drops the connection and hangs, both firefox and chrome. ( in my PC) , now im using the latest firmwares. duet2 wireless.
i have had the same problem before with lower revisions.
i can connect with any of my other devices without issue , just not the PC , unless i restart it.
anyone had this problem, and solved it?

@Phaedrux said in seperate fan controll:

The tool fan slider in DWC is a special slider that is attached to the part cooling fan of the currently selected tool.

so ultimately what i was trying to get going is one fan set up to thermostatically turn on for the tool head when it reaches 45 deg, the second fan can manually be turned on or automatically turned on when a bridging function happens

on duet wifi with latest build

; Fans

M950 F0 C"fan0" Q500 ; create fan0 on pin fan0 and set its frequency
M106 P0 C"part/bridging fan" P1 S0 H-1 ; set fan0 "H-1 disables thermostatic mode" or H1 enables. ("S" parameter turns that fan on or off S0 or S1) (T45 is fan on at 45 degrees)

M950 F1 C"fan1" Q500 ; create (Tool fan 1) on pin fan1 and set its frequency
M106 P1 C"tool fan" S0 H1 T45 ; set (Tool fan 1) value. Thermostatic control is turned off

M950 F2 C"e1heat" Q20000 ; create fan on pin e1heat and set its frequency ( connected to Solid State relay )
M106 P2 C"Neopixels ON/OFF" S1 H-1 ;set fan 2 name and value. Thermostatic control is turned off

M950 F3 C"fan2" Q20000 ; create fan2 on pin fan0 and set its frequency ( connected to Solid State relay )
M106 P3 C"Relay 2 ON/OFF" S0 H-1

it shows up in webface under fan controll as separate fan sliders, named "part/bridging fan" and "tool fan".
the tool fan turns on at 45deg
when a print is started the sliders ( both) do not separate control, but control thepart/bridging fan no matte which slider is moved

What could the issue be?

same problem here exactly as above.., web interface hangs,

@Phaedrux said in g32 reporting:

r if it's a firefox thing. Is

yes win7

@Phaedrux said in g32 reporting:

homeall

No leveling code in Homeall..

you answered it, if it occasionally does this then all is ok.

thanks for the reply

@Phaedrux said in g32 reporting:

The macro you're running in your screenshot is not bed.g

it was a G32 from a macro containing only this:
G32 ; level bed

the above screen shot is what the duet posts back, it is not all the time, like every tenth g32..

here is the problem:

i mean to say when i do a bed level ( only once ) i get many reports back at the same time.

@Phaedrux
thanks for the reply.

Ok so from what i have read makes no sense to me, lol

the picture i have attached shows me clicking on the (Neopixels on/off) tab
Can this tab be an actual button to toggle on and off at full power, and remove the slider ?

this is what i have:

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"Tool fan" P1 S0 H-1 T45 ; set fan 0 value. Thermostatic control is turned on "H-1 disables thermostatic mode" or H1 enables. "S" parameter turns that fan on or off S0 or S1 T45 is fan on at 45 degrees

M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 C"Parts cooling fan" S0 H-1 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"e1heat" Q20000 ; create fan 2 on pin e1heat and set its frequency ( connected to relay )
M106 P2 C"Neopixels ON/OFF" S0 H-1 ;set fan 2 name and value. Thermostatic control is turned off
M950 F3 C"fan2" Q20000 ; create fan 0 on pin fan0 and set its frequency ( connected to relay )
M106 P3 C"Relay 2 ON/OFF" S0 H-1

OR can io create a whole new section under the " fan Control " section just for led and stuff with buttons?

under the dashboard/ fan control.

can a new section be added or created Just to be an ON/OFF button for the led's hooked up to a fan port instead of a Slider bar ?

so ultimatly where it says fan selection, and the "tool fan" tab, can that tab be made to be an on off button instead of a selection button ?

@Phaedrux said in 3.11 signal inverting for endstop:

results of both M122 and M98

i had time to pull it apart and check continuity of everything, all was good
and even more strange it works now. im beginning to think its time to re install windows.

@Phaedrux
ok, thanks for looking

i will test all wiring when i have time

@Phaedrux

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N8PS4-7J9D4-3S86R-KAA3N
Used output buffers: 3 of 24 (10 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 94144 of which 20 recycled
Exception stack ram used: 264
Never used ram: 8664
Tasks: NETWORK(ready,368) HEAT(blocked,1224) MAIN(running,1824) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:15 ago, cause: software
Last software reset at 2020-10-06 18:14, reason: User, spinning module GCodes, available RAM 8408 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 18.3, current 19.3, max 19.5
Supply voltage: min 24.0, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-10-06 18:15:06
Cache data hit count 25697305
Slowest loop: 4.97ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.2ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.62ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address ec:fa:bc:5b:3f:ab
  WiFi Vcc 3.43, reset reason Unknown
  WiFi flash size 4194304, free heap 21640
  WiFi IP address 192.168.0.111
  WiFi signal strength -72dBm, reconnections 0, sleep mode modem
  Socket states: 0 4 0 0 0 0 0 0

and

M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 519C