Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. Billsrf
    3. Topics
    • Profile
    • Following 3
    • Followers 0
    • Topics 7
    • Posts 99
    • Best 0
    • Controversial 0
    • Groups 0

    Topics created by Billsrf

    • Billsrfundefined

      Remapping XY to 6 & 7 on the expansion board for Duet WiFi

      Tuning and tweaking
      • • • Billsrf
      4
      0
      Votes
      4
      Posts
      225
      Views

      Billsrfundefined

      That fixed it!!!! I was entering it from the G-code line. Not on the config. Thank you

    • Billsrfundefined

      Expansion board setup on Duet3D wifi using external controller

      Tuning and tweaking
      • • • Billsrf
      31
      0
      Votes
      31
      Posts
      2.5k
      Views

      moo16undefined

      @Billsrf said in Expansion board setup on Duet3D wifi using external controller:

      my extruder with an external drive. I have the expansion board plugged in with all the step, dir, ena wiring correct

      please,
      can you upload pic pf the wiring?
      or explain how to tap the enable,step and dir?
      is step+/step- --> +A/-A
      dir+/dir- --> +B/-B
      on the expansion board 4 pin driver connector?
      where is the enable plug to?
      is it a different connector on the expansion board ?
      i using duet 3 MB6HC(main board) and expansion 3HC is it possible with that?
      i missing the wiring part.
      tnx beforehead

    • Billsrfundefined

      Z-probe triggers way above table during HOME ALL

      General Discussion
      • • • Billsrf
      38
      0
      Votes
      38
      Posts
      2.1k
      Views

      dc42undefined

      @billsrf said in Z-probe triggers way above table during HOME ALL:

      @dc42 went through the same set up process as described in test and calibrate Z probe, same results as before, it moves down 10 mm then triggers then stops. I did nottice, as it is moving towards the X-Y home position, the IR sensor flashes 3 times like it is just initialized. Never done that before either.

      Perhaps you have a bad crimp connection in the sensor cable, so that one of the 3 wires disconnects at certain XY positions?

    • Billsrfundefined

      Why are my print times so different when using Simplify3D?

      My Duet controlled machine
      • • • Billsrf
      5
      0
      Votes
      5
      Posts
      717
      Views

      dc42undefined

      You can use Duet Web Control or PanelDue to simulate printing a file, which will give you an accurate print time. In Duet Web Control, Go to the GCode Files page (or GCode Jobs if you are using DWC 2.0beta), right click on the file you want, and click Simulate. When the simulation completes it will tell you how long it will take to print. It also writes the simulated time to the end of the file so that it can be retrieved later.

      PanelDue and DWC 2.0beta display the simulated print time as part of the file properties. DWC2.0 beta also uses the simulated time to give you an estimated print completion time when you come to print the file.

    • Billsrfundefined

      Running Bed Mesh Compensation

      Tuning and tweaking
      • • • Billsrf
      39
      0
      Votes
      39
      Posts
      3.8k
      Views

      Phaedruxundefined

      @billsrf Glad it's sorted out.

    • Billsrfundefined

      Thermocouple Faults to 2000

      Duet Hardware and wiring
      • • • Billsrf
      37
      0
      Votes
      37
      Posts
      3.1k
      Views

      Phaedruxundefined

      @billsrf said in Thermocouple Faults to 2000:

      @phaedrux I'm confused! What does the XY value have to do with the nozzle going straight down in to the bed on Z axis?

      It may not have anything to do with your current issue but it may cause further issues down the line. Such a large offset could cause your printer to think it is printing half a meter off your build surface when it probes at the edge. Generally the probe is as close to the nozzle as possible. I doubt it is half a meter, but I don't know your printer.

      Glad you got it sorted out though.

    • Billsrfundefined

      Homing issues

      General Discussion
      • • • Billsrf
      8
      0
      Votes
      8
      Posts
      1.2k
      Views

      dc42undefined

      See https://duet3d.com/wiki/Configuring_RepRapFirmware_for_a_Cartesian_printer#Homing_Z.