Best posts made by peirof

Hi,

I have find this video, seems promising
NON PLANAR LAYERS](https://youtu.be/km1lvuva5mI)

@phaedrux do it, works.... FW3 save me the ass

@engikeneer said in Help with Slic3r PE 2.2:

ou tried enabling 'support on

ey....

this is, thanks @engikeneer

Hi,

think i have find it...

After several tests, I saw that the problem was always similar, it did not matter the material, the layer height, the speed of printing ... after 1 or 2 layers, jamming occurred, and loss of steps of the heater, which another part is a double gear striker, and the voltage was raised to 800 mA in config.g.

Seeing the stuck filament, it looked like the tip formed a ball, and the distance coincided, approximately where the nozzle began.

At this point I have to say that I use a Prometheus v2 hotend ... seeing the documentation of this, I saw an error when I mount it ... and I did not put Thermal Silicone on the nozzle, so I put thermal silicone and gave it more distance the Heat Block to the Heat Skin. Before I had 2 mm, and I have put two nuts, in addition to 2 mm. In total about 6 mm, which forced me to modify the config.g, and adjust the loss of height effect

With this I tried to separate the source of heat, Heat Block, Heat Skin, and try to get the heat, did not reach the Heat Skin, and did not melt the material, this along with the silicone ends, it seems that it is working.

I have two impressions, with ABS, and for now, everything is correct, I still need to try PETG, which uses a higher temperature ...

I share my evidence here, in case you can serve someone ...

The truth is that it would have had more influence, if the silicone, or separate the Heat Block from the Heat Skin ...

@tripz2757 said in Tevo little monster:

ant get it to

i have a TLM modded with Duet... in what can i help you?

Simplify 3d

Hi,

Find it...!!!

Thanks to all.

Mechanical issue, the screw on one arm was not tight

@pickett said in Best Z Probe for Duet 3 Mini 5+:

@peirof that is what I keep hearing about that particular setup so have you heard any good things about the generic precision piezo off of Amazon.com?

iI haven't heard anything, I bought it from Precision Piezo web ...

Hi,

Info obtained from E3d wiki, copy and paste..

 Before you install your heater cartridge, you should double check that you both purchased and received the correct voltage cartridge. Cartridges are laser etched with their voltage, but all it is worth double-checking anyway. This process is less annoying than putting out a house fire.
 
 If you have a 12v30w heater cartridge, your multimeter should read 4.8Ω
 
 If you have a 24v30w heater cartridge, your multimeter should read 19.2Ω
 
 Your cartridges resistance may deviate slightly from these numbers, which is fine. We're mostly interested in verifying which cartridge type you have.
 
 If you have a 12v 40w heater cartridge your multimeter should read 3.6Ω
 
 If you have a 24v 40w heater cartridge your multimeter should read 14.4Ω

Hi,

As I have commented in other recent posts, after my problems with my TLM. I'm going to start from almost 0 (I'll take advantage of some components) and I'm going to build a Corexy (RatDig v3)

In a Facebook group, from this printer, I have been passed an interesting document about the recommended tension for the belts. I take it for granted, and I post it here, in case it serves anyone

BELT TENSION

Hi,

It might be interesting to add the integration with email. In two ways I can think of: that an email will be sent when events will pass (change of layer, some error, no filament, state of the print,....) and that I could make orders (gcodes with established format) when I received an email.. I find this difficult and unutilitarian

We are near celebrate that @dc42 it's near.... 20000 post....

In this moment.. 19995....

Not sure.... But seems development its stopped... Since July without updates

Hi,

I have encounter this info in a Facebook group...

Golden ratio in Delta printer

Hi,

Prusa printers have launch a freehold ebook of concepts of 3d printing....
I have see a few and can say its very good...

I wish I had that book when I started ... Some time ago nothing happened to me on the forum ... I take this opportunity to congratulate everyone on Christmas ...

Happy holidays and a happy new year ... May the Covid be kind to you ...

P. D.: If anyone has the link to the vaccine for the Covid from Thingiverse ... Let them put it .....

@jay_s_uk

think can be this, now i am not in home.

Extruder stepper motor its connected to Shocket E0_MOTOR, this correspond to Drive 3. No?

but, now, i am not sure. Its possible that Extruder stepper its connected to Shocket E1_Motor, thar correspond to Drive 4....

Later check

@jay_s_uk said in I am near.... but:

M584 X0 Y1 Z2 E3
@jay_s_uk since NOW you are one of the my best friends..... solved. Now extruder appears in DWC.....

Thx to all

@jay_s_uk

thanks i will try, i put reports after

Hi,

What advantages / diferences has connect direct to Duet 3 mini vs rasperry pi-->duet 3 mini?

@fcwilt yes