@bastien said in 3D GCode Viewer integrated with DWC:

i just install 3.2, i viewer in sub menu in files but no in main menu

it's ok, i re install plug in and start in new plug in menu

@phaedrux sorry, I have a delta 'predator' with. a duet 2 wifi, with my previous motors I had no problem, one of my motors blocked, so I wanted to change the 3, I think it can only become connections and I don't know which reversed wire I connected well in the order of the technical doc but with Chinese as they have not changed the order of the wires

Hi,
I changed my nema motors, and they no longer stop in home, yet the endstop LEDs go out when they are in possition
Motor wiring problem?

@bberger said in firmware retraction:

this. the 3.4 betas are known (and confirmed) to have a retraction issue..

it's ok after update thanks

@deckingman
my config.g

G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"Predator"                               ; set printer name
M665 L440.000 R221 B185.0 H456                       ; Set delta radius, diagonal rod length, printable radius and homed height M665 L415.000 R222.5 B185.0 H486  ; rod alu
M666 X0 Y0 Z0 A0.00 B0.00                                  ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S1                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet

; Drives
M569 P0 S0                                     ; physical drive 0 goes forwards
M569 P1 S0                                     ; physical drive 1 goes forwards
M569 P2 S1                                     ; physical drive 2 goes forwards
M569 P3 S1                                     ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X160 Y160 Z160 E392.5 ; set steps per mm
M566 X1000 Y1000 Z1000 E1000       ; set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z12000 E1200    ; set maximum speeds (mm/min)
M201 X3000 Y3000 Z3000 E3000       ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E1000 I30                ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        ; Set idle timeout



; Axis Limits
M208 Z0 S1                                     ; set minimum Z

; Endstops
M574 X2 S1 P"xstop"                            ; configure active-high endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop"                            ; configure active-high endstop for high end on Y via pin ystop
M574 Z2 S1 P"zstop"                            ; configure active-high endstop for high end on Z via pin zstop

; Z-Probe
M558 P5 C"e0stop" H8 F120 T6000            ; set Z probe type to switch and the dive height + speeds
M558 H10                                       ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
G31 P500 X0 Y0 Z14.95                        ; set Z probe trigger value, offset and trigger height
M557 R175 S20                               				; Define mesh grid
G29 S1                                  

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4300 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00                               ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S80                                    ; set temperature limit for heater 0 to 80C
M308 S1 P"e0temp" Y"thermistor" T100000 B4300  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on
 

; Tools
M563 P0 D0 H1 F0                               ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Retraction
;M207 S4.0 F5000 R-0.025 T2500 Z0.5
M207 S6.5 F3700 Z0.1


; Custom settings are not defined
; Custom settings are not configured
;M572 D0 S0.1												; Pressure Advance
;M591 D0 P2 C"e1stop" S0											; Activate filament sensor
M404 N1.75 													; Set for print monitor
;M592 D0 A0.07772 B-0.00029 		; Nonlinear extrusion. Set parameters for extruder drive 0
; Miscellaneous
M575 P1 S1 B57600                              ; enable support for PanelDue

M501

@droftarts I had thought about it, but I am in relative extrusion, and I have M83 at the beginning of my config.g, when the retraction is managed by the slicer, everything is fine, but not the firmware

I enabled firmware retraction in cura
after M207
Tool 0 retract/reprime: length 5.00/5.00mm, speed 50.0/50.0mm/sec, Z hop 0.10mm

hello, I wanted to test the firmware retraction but I have a problem, with the same settings as my slicer, my filament moves back with each retraction to the point where it no longer feeds the tool, M207 S5 F3000 Z0.1

Circuit: Duet 2 WiFi (2WiFi)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.0beta7+7 (2022-01-14)
Duet WiFi Server Version: 1.23

the last update of the bot on github is more than 3 years old,
the project was abandoned

it's ok with b7+7, thanks

for me, b7+4 don't resolve problem