@phaedrux sorry, I have a delta 'predator' with. a duet 2 wifi, with my previous motors I had no problem, one of my motors blocked, so I wanted to change the 3, I think it can only become connections and I don't know which reversed wire I connected well in the order of the technical doc but with Chinese as they have not changed the order of the wires
Posts made by bastien
-
RE: Motor don't stop to homeposted in Duet Hardware and wiring
-
Motor don't stop to homeposted in Duet Hardware and wiring
Hi,
I changed my nema motors, and they no longer stop in home, yet the endstop LEDs go out when they are in possition
Motor wiring problem? -
RE: firmware retractionposted in Using Duet Controllers
@bberger said in firmware retraction:
this. the 3.4 betas are known (and confirmed) to have a retraction issue..
it's ok after update thanks
-
RE: firmware retractionposted in Using Duet Controllers
@deckingman
my config.gG90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Predator" ; set printer name M665 L440.000 R221 B185.0 H456 ; Set delta radius, diagonal rod length, printable radius and homed height M665 L415.000 R222.5 B185.0 H486 ; rod alu M666 X0 Y0 Z0 A0.00 B0.00 ; put your endstop adjustments here, or let auto calibration find them ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S1 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S0 ; physical drive 0 goes forwards M569 P1 S0 ; physical drive 1 goes forwards M569 P2 S1 ; physical drive 2 goes forwards M569 P3 S1 ; physical drive 3 goes forwards M584 X0 Y1 Z2 E3 ; set drive mapping M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X160 Y160 Z160 E392.5 ; set steps per mm M566 X1000 Y1000 Z1000 E1000 ; set maximum instantaneous speed changes (mm/min) M203 X12000 Y12000 Z12000 E1200 ; set maximum speeds (mm/min) M201 X3000 Y3000 Z3000 E3000 ; set accelerations (mm/s^2) M906 X1000 Y1000 Z1000 E1000 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 Z0 S1 ; set minimum Z ; Endstops M574 X2 S1 P"xstop" ; configure active-high endstop for high end on X via pin xstop M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop ; Z-Probe M558 P5 C"e0stop" H8 F120 T6000 ; set Z probe type to switch and the dive height + speeds M558 H10 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved G31 P500 X0 Y0 Z14.95 ; set Z probe trigger value, offset and trigger height M557 R175 S20 ; Define mesh grid G29 S1 ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4300 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S80 ; set temperature limit for heater 0 to 80C M308 S1 P"e0temp" Y"thermistor" T100000 B4300 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Retraction ;M207 S4.0 F5000 R-0.025 T2500 Z0.5 M207 S6.5 F3700 Z0.1 ; Custom settings are not defined ; Custom settings are not configured ;M572 D0 S0.1 ; Pressure Advance ;M591 D0 P2 C"e1stop" S0 ; Activate filament sensor M404 N1.75 ; Set for print monitor ;M592 D0 A0.07772 B-0.00029 ; Nonlinear extrusion. Set parameters for extruder drive 0 ; Miscellaneous M575 P1 S1 B57600 ; enable support for PanelDue M501 -
RE: firmware retractionposted in Using Duet Controllers
@droftarts I had thought about it, but I am in relative extrusion, and I have M83 at the beginning of my config.g, when the retraction is managed by the slicer, everything is fine, but not the firmware
-
RE: firmware retractionposted in Using Duet Controllers
I enabled firmware retraction in cura
after M207
Tool 0 retract/reprime: length 5.00/5.00mm, speed 50.0/50.0mm/sec, Z hop 0.10mm -
firmware retractionposted in Using Duet Controllers
hello, I wanted to test the firmware retraction but I have a problem, with the same settings as my slicer, my filament moves back with each retraction to the point where it no longer feeds the tool, M207 S5 F3000 Z0.1
Circuit: Duet 2 WiFi (2WiFi)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.0beta7+7 (2022-01-14)
Duet WiFi Server Version: 1.23 -
RE: Duet Telegram botposted in General Discussion
the last update of the bot on github is more than 3 years old,
the project was abandoned -
RE: Printer don't heat after longer in IDLE state 3.4b7+1posted in Beta Firmware
it's ok with b7+7, thanks
-
RE: Printer don't heat after longer in IDLE state 3.4b7+1posted in Beta Firmware
for me, b7+4 don't resolve problem
-
RE: setting Retraction after restartposted in General Discussion
@siam it works, in config after line 68, thanks
-
RE: setting Retraction after restartposted in General Discussion
Even with T0 before, the settings are not loaded, I also tested to keep only the filament config, same result after a restart,
while waiting to find a solution, I will put it in my macro, start print, so as not to forget -
RE: setting Retraction after restartposted in General Discussion
I will test, but normally the setting of the filament config will have to be taken care of on T0 then that the filament is loaded
-
RE: setting Retraction after restartposted in General Discussion
Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.1.4 on Thu Aug 27 2020 18:42:39 GMT+0200 (heure d’été d’Europe centrale) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Predator" ; set printer name M665 L440.000 R226 B185.0 H456 ; Set delta radius, diagonal rod length, printable radius and homed height M666 X0 Y0 Z0 A0.00 B0.00 ; put your endstop adjustments here, or let auto calibration find them ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S1 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S0 ; physical drive 0 goes forwards M569 P1 S0 ; physical drive 1 goes forwards M569 P2 S0 ; physical drive 2 goes forwards M569 P3 S1 ; physical drive 3 goes forwards M584 X0 Y1 Z2 E3 ; set drive mapping M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X80 Y80 Z80 E498.8; set steps per mm M566 X1000 Y1000 Z1000 E1000 ; set maximum instantaneous speed changes (mm/min) M203 X12000 Y12000 Z12000 E1200 ; set maximum speeds (mm/min) M201 X3000 Y3000 Z3000 E3000 ; set accelerations (mm/s^2) M906 X1000 Y1000 Z1000 E1000 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Retraction M207 S4.0 F5000 Z0.5 ; Axis Limits M208 Z0 S1 ; set minimum Z ; Endstops M574 X2 S1 P"xstop" ; configure active-high endstop for high end on X via pin xstop M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop ; Z-Probe M558 P5 C"e0stop" H8 F120 T6000 ; set Z probe type to switch and the dive height + speeds M558 H10 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved G31 P500 X0 Y0 Z17.0 ; set Z probe trigger value, offset and trigger height M557 R175 S20 ; Define mesh grid G29 S1 ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4300 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S80 ; set temperature limit for heater 0 to 80C M308 S1 P"e0temp" Y"thermistor" T100000 B4300 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined ; Custom settings are not configured M572 D0 S0.1 ; Pressure Advance ;M591 D0 P2 C"e1stop" S0 ; Activate filament sensor M404 N1.75 ; Set for print monitor M592 D0 A0.07772 B-0.00029 ; Nonlinear extrusion. Set parameters for extruder drive 0 ; Miscellaneous M575 P1 S1 B57600 ; enable support for PanelDue M501 -
setting Retraction after restartposted in General Discussion
hi, after restarting my printer i lost the retraction setting
however I have M207 S4.0 F5000 Z0.5 in config.g and also in filament config,
but after a restart I have 2mm retraction at 16mm / s
what did I miss? -
RE: lost wifi after printposted in General Discussion
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3beta1 running on Duet WiFi 1.02 or later
WiFi firmware version 1.23 -
lost wifi after printposted in General Discussion
hi
since update to 3.3 beta1 my duet lost connection wifi afer print,
i testing, in my finish print macro the command gcode M552 S-1 and M552 S1,a rescue solution