First one in Canada?!
My Ender 3 Pro will be happy! The last of my FDM printers not in Duet!
tech wiz
First one in Canada?!
My Ender 3 Pro will be happy! The last of my FDM printers not in Duet!
nevermind, I just read some more and SBC (I thought SBC standed for single board computer aka standalone mode, I was wrong) is the RPi mode and the SD card isn't supposed to be in for the RPi mode.
@engikeneer Homeall.g, all homes and bed.g are all clean.
I ain't a reference, but i'm using 3.1.1 on my 3x Duet 3 6HC boards and it has been flawless.
(Railcore II 300ZL, Tronxy X5SA-500 Pro, Ender 3 Pro)
Just bought 2 WyzecamV2 just for this.
Turns out I can't connect to them (either of them).
The app works well, I see the RTSP feed via VLC, but I cannot connect to it through either ssh or www (http://xxx.xxx.xxx.xxx nor https://xxx.xxx.xxx.xxx)
Any idea? I did extract all files to a microSD, edited the files on it as per instructions (wpa file, not the network).
as mentioned, works well in the app, VLC, even coupled to my Synology NAS, but can'T get it to work...
@droftarts What would be the best line to add to my start gcode to tell it to reheat to the slicer's defined heat and wait for temp reached then proceed?
Can I simply add:
M116 H0 S5
after the homing?
I could not get my BL touch to work at all on ports IO6 and IO7. Only when plugged on IO5 did it work.
I'd try that first, easy swap.
I found a way to make it work. I grinded down the location of the bearings in the indirect filament casing to bring lower the shaft and now it has enough pressure to make the filament turn the shaft. Getting 196 to 226 readings. Very happy!
Would still be nice if it was possible to use the switch only in case of temporary failure..
Do you have something defined in config-override.g concerning tools?
Might be weird, but did you try to remove the tool label S"T0" in M563?
Mine is like this:
; Tools
M563 P0 D0 H1 F1 ; define tool 0
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
Hello guys,
I've searched long and hard to find the model of the screen I have for this printer but I cannot figure out anything else than 12864ZW-10.
Will it fit with a Duet 3 Mini 5+?
It is the original display that was on the customer's CR-10 (original)
@Phaedrux YOU DON'T COUNT!
haha
First one in Canada?!
My Ender 3 Pro will be happy! The last of my FDM printers not in Duet!
Should get mine dec 31st from filastruder.com.
It will go in a Ender 3 Pro stock with BL touch.
I'll try to do a nice writeup and how to.
Well I followed a bunch of these recommendations and you know what? Success! The print is very clean and very solid.
I slowed down to 40mm/s
increased to 0.82mm layer width
Slowed fan to 25%
Layer height at 0.52mm
Temp at 225°
@Veti The Nozzle for the Volcano is different, it has longer threads.
I'll try Phaedrux's idea of increasing temperature.
On a side note though, the plastic does come out super easily when printing at these speeds. It works great for smaller prints and for the first 3-4 layers. It'S the walls that are not sticking.
I'll try some of these answers tonight and will report back.
Well I have the Chimera+ on it, which I paid lots of $ for. would suck to toss that away.
Thanks for the pointers. It makes sense.
I will look into either slowing it down or getting a smaller nozzle (which would suck because it's a NozzleX at 50$CDN)