Hi Will, we are expecting more stock towards the end of this week.

We have a limited number back in stock now with more due next week.

I have two unused, untouched Duet Wifi that I would be willing to sell, for anyone interested. They are from Sept 2016, production run. I'm located in Vancouver, Canada. I'm not actively looking to sell, but if anyone happens to need one desperately, I'd sell them. (The printers the wifis would go in will be getting duet ethernets when I build them, hence why I'm willing to sell)

Thanks for the info

placed an order. thank you from fantastic support!

Thanks! Check your email again.

@T3P3Tony:

Hi

Apologies they were temporatily out of stock, we received more of both the 5 and the 7 inch today so they are now back in stock.

Ok, thanks, I was just wondering 🙂

Niiiice

Thanks for your reaction. The reseller just contacted me and garanteed me to ship my order tommorow morning.

Hi Pascal

Please contact your reseller for a warranty exchange referencing this forum thread, if you bought it direct from Duet3d.com then please send me an email referencing your order number.

Cheers

Tony

@baballuci:

I'm using the Duet Wifi on my Hypercube, it's much much better than the RAMPS i was using.

Will you share the config files for the hypercube? I build one and waiting for the duet at this moment. With my ramps it printed fine but i think the duet will show off real good prints.

Hi we don't sell the BL touch, rather put off by their lack of openness and trying to patent something that had been discussed in the community for some time.

Thanks!

I will message you

Thanks, will buying today

Can I ask for the mini ir sensor? Don't see in addons

@Fickert:

Can't wait to get my duet in! Also on the FT-5 Train and will later be doing a build log for the whole thing 🙂

https://drive.google.com/file/d/0Bxi0uBhn1toSUXJFYTl4d0g0QjQ/view?usp=sharing

Awesome. Just for reference:

[c]
;;
;; Folgertech FT5 Configuration
;;

M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X308 Y308 Z360 S0 ; Set axis maxima

M574 Y2 X2 Z0 S0 ; Define active high microswitches

M558 P1 X0 Y0 Z1 H5 F120 T6000 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds
G31 P500 X0 Y0 Z2.56 ; Set Z probe trigger value, offset and trigger height

M584 X0 Y1:4 Z2 E3 ; Map to specific drives

M569 P0 S0 ; Drive 0 goes forwards - X
M569 P1 S0 ; Drive 1 goes forwards - Y
M569 P2 S1 ; Drive 2 goes forwards - Z
M569 P3 S1 ; Drive 3 goes forwards - E0
M569 P4 S1 ; Drive 3 goes forwards - Y

M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 Z399 E492.45 ; Set steps per mm
M566 X1200 Y1200 Z60 E120 ; Set maximum instantaneous speed changes (mm/min)
M203 X8000 Y8000 Z600 E1200 ; Set maximum speeds (mm/min)
M201 X1500 Y1500 Z500 E250 ; Set accelerations (mm/s^2)
M906 X1000 Y1000 Z1200 E900 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

M143 S260 ; Set maximum heater temperature to 260C
M305 P0 T100000 B3950 C0 R4700 ; Set thermistor + ADC parameters for heated bed (Heater 0)
M305 P1 T100000 B4388 C0 R4700 ; Set thermistor + ADC parameters for E0 (Heater 1)

M307 H0 A281.7 C430.4 D4.4 B0 ; Bed PID
M307 H1 A344.7 C122.8 D5.5 B0 ; Hotend PID

M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

M550 PFT5 ; Set machine name
M552 P0.0.0.0 S1 ; Enable network and acquire dynamic address via DHCP

M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S255 I0 F500 H1 T50 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S255 I0 F500 H1 T50 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

T0 ; Select first tool
[/c]

everything is sorted out 🙂 Thanks for excelent and quick service guys!

We have about a dozen left at Filastruder.

Hey I have sent you an email.