Accelerometer Usage

[tekstyle]

@phaedrux oh ok. i'll wait for that in the meantime. Thank you.

[o_lampe]

@jbergene
mine says "DSH" clearly, not sure what a DH should show? Anyone?

[oliof]

18.8.2021, 07:37:18 M955 P0
Accelerometer 0 type LIS3DH with orientation 20 samples at 1344Hz with 10-bit resolution, SPI frequency 2000000

[jbergene]

@o_lampe Yeah maybe ill just try the DSH that arrived yesterday. that one says
2304 - DSH - YP3HC"

Do you know the orientation of the purple LISD3DSH board? X Y Z
I cant find that information anywhere

[o_lampe]

@jbergene

According to this picture

• positive X goes to the right
• positive Y goes to the back
• positive Z goes up

[jbergene]

@o_lampe thank you:)

[tekkydave]

@gloomyandy I bought one from that seller. The board seems to indicate a LIS3DSH but the chip has 3CH on it which is a LIS3DH. Have you connected it up & what does the Duet report?

I bought two boards from different sellers. One should be a LIS3DH and the other a LIS3DSH. They look identical to me and both have 3CH on the chip.
The only difference is one has OED26 after the 3CH and the other OED27.
I have only connected the OED26 to the Duet so far.

They both look like this on the back:

I'm assuming that the Duet will report the correct chip.

Edit: I have soldered a connector to the other one (OED27) and tested it with the Duet. Also get same message as the other one

Accelerometer 0 type LIS3DH with orientation 14 samples at 1344Hz with 10-bit resolution, SPI frequency 2000000

Hmmmpphhh!

Edit:
Further tests connecting the device to an Arduino confirm it is a LIS3DH as it returns device id = 51 (0x33). So despite it being advertised as a LIS3DSH and the pcb indicating that it is - well it isn't. So be careful when buying these folks and check the code on the chip:
3CH = LIS3DH
DSH = LIS3DSH

I have ordered another one from the link given by @dc42 above. Let's see what turns up

[gloomyandy]

@tekkydave Mine is marked C3H OED27. Not had chance to try it yet.

[tekkydave]

@gloomyandy It is a LIS3DH then. I have just run some tests connecting one up to an Arduino. I can only get it to communicate using an LIS3DH library.

[gloomyandy]

@tekkydave Have just tested mine and RRF 3.4 seems to think it is a LIS3DH, which is a pain as I really wanted a LIS3DSH to test with (I look after the RRF STM32/LPC port). Oh well looks like I need to try and order from a different supplier.#

[tekkydave]

@gloomyandy

[Blacksheep99]

@tekkydave said in Accelerometer Usage:

@gloomyandy I bought one from that seller. The board seems to indicate a LIS3DSH but the chip has 3CH on it which is a LIS3DH. Have you connected it up & what does the Duet report?

I bought two boards from different sellers. One should be a LIS3DH and the other a LIS3DSH. They look identical to me and both have 3CH on the chip.
The only difference is one has OED26 after the 3CH and the other OED27.
I have only connected the OED26 to the Duet so far.

They both look like this on the back:

I'm assuming that the Duet will report the correct chip.

Edit: I have soldered a connector to the other one (OED27) and tested it with the Duet. Also get same message as the other one

Accelerometer 0 type LIS3DH with orientation 14 samples at 1344Hz with 10-bit resolution, SPI frequency 2000000

Hmmmpphhh!

Edit:
Further tests connecting the device to an Arduino confirm it is a LIS3DH as it returns device id = 51 (0x33). So despite it being advertised as a LIS3DSH and the pcb indicating that it is - well it isn't. So be careful when buying these folks and check the code on the chip:
3CH = LIS3DH
DSH = LIS3DSH

I have ordered another one from the link given by @dc42 above. Let's see what turns up

I ordered one from the seller DC42 linked to and this is what I received.

[tekkydave]

@blacksheep99 should be a LIS3DSH from the chip id of DSH.

[tecno]

Got my 2 today from UK and they show up as:

M955 P0 C"io3.out+io3.in"
Accelerometer 0:0 type LIS3DSH with orientation 20 samples at 1600Hz with 16-bit resolution, SPI frequency 2000000

So what do I need to do next to get started? I have one for X and Z and the other for Y only.

[jay_s_uk]

@tecno if you have a bedslinger, then yes.
and then use the input shaper plugin to record the results

[tecno]

@jay_s_uk

Yes its my good old Chiron

Will try to see what I get here.

[tecno]

Re ORIENTATION

As i see this is orientation I20, right?

If I flip the board so VCC will be to the right upside down is the orientation then I60 ?

How do handle this in config.g ? 2 lines ?

M955 P0 I20 C"io3.out+io3.in" ;active
;M955 P0 I60 C"io3.out+io3.in" ; not active

[tekkydave]

@tecno Yes 60.

0 = +X, 1 = +Y, 2 = +Z, 4 = -X, 5 = -Y, 6 = -Z.

the chip's z will be pointing in printer's -z dir = 6
the chip's x will be pointing in printer's +x dir = 0

[tecno]

@tekkydave
Thanks, just want to be sure.

[tekkydave]

I have finally got my hands on a LIS3DSH. I ordered it from the link supplied above by @dc42

https://www.ebay.co.uk/itm/272706183865

Note the 'DSH' on the chip

And in DWC: