Happy easter everyone!
@dc42
I haven't really had any issues with crashes in a while now, since "we" finally got the printer working again after patching out the extrusion bug I've had the printer going more or less non-stop and only with one instance of OrcaSlicer open and checking in on my phone (android & chrome browser) every now and then to not provoce any crashes.
However when I got to the printer this morning i saw it had rebooted during the night for some reason!
Here is the last entries to the eventlog (had to switch to event logging since debug it putting out SO MUCH DATA since a little while back):
2024-03-29 13:56:58 [warn] Started printing file 0:/gcodes/O*********r_0.2mm_ABS_0.4n_17m37s.gcode
2024-03-29 14:01:54 [warn] M150 sent for logo : yellow
2024-03-29 14:01:54 [warn] M150 sent for nozzle : yellow
2024-03-29 14:02:14 [warn] M150 sent for logo : teal
2024-03-29 14:02:14 [warn] M150 sent for nozzle : bright_white
2024-03-29 14:02:28 [warn] M150 sent for logo : green
2024-03-29 14:02:28 [warn] M150 sent for nozzle : bright_white
2024-03-29 14:02:42 [warn] 9 points probed, min error -0.014, max error 0.005, mean -0.005, deviation 0.005
Height map saved to file 0:/sys/heightmap.csv
2024-03-29 14:02:43 [warn] M150 sent for logo : dim_gray
2024-03-29 14:02:43 [warn] M150 sent for nozzle : dim_red
2024-03-29 14:02:44 [warn] M150 sent for logo : yellow
2024-03-29 14:02:44 [warn] M150 sent for nozzle : yellow
2024-03-29 14:03:09 [warn] M150 sent for logo : light_blue
2024-03-29 14:03:09 [warn] M150 sent for nozzle : bright_white
2024-03-29 14:03:20 [warn] M150 sent for logo : red
2024-03-29 14:03:20 [warn] M150 sent for nozzle : bright_white
2024-03-29 14:24:21 [warn] Finished printing file 0:/gcodes/O*********r_0.2mm_ABS_0.4n_17m37s.gcode, print time was 0h 27m
2024-03-29 14:24:26 [warn] M150 sent for logo : dim_gray
2024-03-29 14:24:26 [warn] M150 sent for nozzle : dim_red
2024-03-29 20:05:42 [warn] HTTP client 192.168.10.xx disconnected
2024-03-30 09:31:09 [warn] HTTP client 192.168.10.xxx login succeeded (session key 2606324820)
2024-03-30 09:44:34 [warn] HTTP client 192.168.10.xx login succeeded (session key 2283911350)
2024-03-30 17:13:44 [warn] HTTP client 192.168.10.xx login succeeded (session key 702406583)
power up + 00:00:03 [info] Event logging started at level warn
power up + 00:00:03 [info] Running: Duet 3 Mini5plus WiFi: 3.5.0-rc.3+5 (2024-03-27 11:34:04)
power up + 00:00:04 [warn] WiFi module started
power up + 00:00:04 [warn] M150 sent for logo : n/a
power up + 00:00:04 [warn] M150 sent for nozzle : n/a
power up + 00:00:05 [warn] M150 sent for logo : n/a
power up + 00:00:05 [warn] M150 sent for nozzle : n/a
power up + 00:00:09 [warn] WiFi module is connected to access point RV32-IOT2G, IP address 192.168.10.x
power up + 00:00:10 [warn] HTTP client 192.168.10.xx login succeeded (session key 1857804272)
2024-03-31 03:37:09 [warn] Date and time set at power up + 00:00:10
And some reports:
M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.5.0-rc.3+5 (2024-03-27 11:34:04) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: XNHXF-HR6KL-K65J0-409N2-K9W1Z-RV2MZ
Used output buffers: 18 of 40 (31 max)
=== RTOS ===
Static ram: 103264
Dynamic ram: 124000 of which 12 recycled
Never used RAM 11284, free system stack 180 words
Tasks: NETWORK(2,nWait 7,245.0%,231) HEAT(3,nWait 6,0.4%,326) Move(4,nWait 6,0.0%,341) CanReceiv(6,nWait 1,0.9%,771) CanSender(5,nWait 7,0.0%,337) CanClock(7,delaying,0.1%,349) TMC(4,nWait 6,12.7%,102) MAIN(1,running,113.1%,667) IDLE(0,ready,13.9%,30) AIN(4,delaying,13.1%,260), total 399.3%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 08:29:06 ago, cause: software
Last software reset at 2024-03-31 02:36, reason: HardFault invState, Platform spinning, available RAM 6444, slot 2
Software reset code 0x4060 HFSR 0x40000000 CFSR 0x00020000 ICSR 0x00000803 BFAR 0xe000ed38 SP 0x20012020 Task NETW Freestk 495 ok
Stack: 2002c5f8 20030ba8 200014e8 00000000 ffffffff 0002ffb1 00000000 60010000 00000000 00000000 00000000 00000000 200120a0 00000014 b5dd8a35 00000002 e8610050 640aa8c0 080001a8 00000001 000347f9 2002c3c0 2002c3c0 00000007 0002f72d 20011744 00000000
Error status: 0x00
Aux0 errors 0,0,0
MCU revision 3, ADC conversions started 30546654, completed 30546654, timed out 0, errs 0
MCU temperature: min 33.8, current 35.5, max 37.6
Supply voltage: min 3.8, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/32, heap memory allocated/used/recyclable 2048/664/248, gc cycles 6669
Events: 1 queued, 1 completed
Driver 0: standstill, SG min 0, read errors 0, write errors 0, ifcnt 13, reads 34825, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 1: standstill, SG min 0, read errors 0, write errors 0, ifcnt 13, reads 34825, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 2: standstill, SG min 0, read errors 0, write errors 0, ifcnt 13, reads 34825, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 3: standstill, SG min 0, read errors 0, write errors 0, ifcnt 13, reads 34823, writes 13, timeouts 1, DMA errors 0, CC errors 0, failedOp 0x51
Driver 4: standstill, SG min 0, read errors 0, write errors 0, ifcnt 13, reads 34824, writes 13, timeouts 1, DMA errors 0, CC errors 0, failedOp 0x6c
Driver 5: not present
Driver 6: not present
Date/time: 2024-03-31 12:06:09
Cache data hit count 4294967295
Slowest loop: 27.00ms; fastest: 0.12ms
=== Storage ===
Free file entries: 18
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 7.8ms, write time 45.9ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, min interval 0, bad calcs 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.4
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is doing "G4 P250" in state(s) 0 0, running macro
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000803
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== Filament sensors ===
check 0 clear 0
Extruder 0 sensor: no filament
=== CAN ===
Messages queued 274931, received 626212, lost 0, errs 369, boc 0
Longest wait 2ms for reply type 6053, peak Tx sync delay 8721, free buffers 26 (min 25), ts 152733/152732/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 10.10ms; fastest: 0.00ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
=== WiFi ===
Interface state: active
Module is connected to access point
Failed messages: pending 0, notrdy 0, noresp 0
Firmware version 2.1beta7
MAC address c4:5b:be:ce:91:93
Module reset reason: Power up, Vcc 3.38, flash size 2097152, free heap 36388
WiFi IP address 192.168.10.x
Signal strength -46dBm, channel 6, mode 802.11n, reconnections 0
Clock register 00002001
Socket states: 0 0 0 0 0 0 0 0
M122 B121
Diagnostics for board 121:
Duet TOOL1LC rev 1.1 or later firmware version 3.5.0-rc.3+5 (2024-03-27 11:29:09)
Bootloader ID: SAMC21 bootloader version 2.8 (2023-07-25)
All averaging filters OK
Never used RAM 3960, free system stack 136 words
Tasks: Move(3,nWait 7,0.0%,127) HEAT(2,nWait 6,6.0%,107) CanAsync(5,nWait 4,0.0%,55) CanRecv(3,nWait 1,0.2%,71) CanClock(5,nWait 1,0.3%,59) ACCEL(3,nWait 6,0.0%,53) TMC(2,nWait 6,53.8%,53) MAIN(1,running,255.9%,315) IDLE(0,ready,0.0%,27) AIN(2,delaying,76.9%,112), total 393.2%
Owned mutexes:
Last reset 08:29:46 ago, cause: power up
Last software reset at 2024-03-12 16:55, reason: StackOverflow, available RAM 2968, slot 0
Software reset code 0x0100 ICSR 0x0042600e SP 0x20007f34 Task Move Freestk 3342 ok
Stack: 20004a80 20004ab4 0001cf33 20004c98 20004938 00000000 0001c011 20003320 fffffffd a5a5a5a5 00000000 20007f8c 00000000 20007f8c 0001cc97 00000000 200017c4 20001748 0001c4d7 20001748 200017c4 00000032 454c4449 00022700 0001ac77 200018e0 200018e0
Driver 0: pos 0, 568.8 steps/mm, standstill, SG min 0, read errors 0, write errors 0, ifcnt 11, reads 23207, writes 11, timeouts 2, DMA errors 0, CC errors 0, failedOp 0x6a, steps req 0 done 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0, segs 0, step errors 0, maxLate 0 maxPrep 0, maxOverdue 0, maxInc 0, mcErrs 0, gcmErrs 0, ebfmin 0.00 max 0.00
Peak sync jitter -4/10, peak Rx sync delay 219, resyncs 0/0, no timer interrupt scheduled
VIN voltage: min 24.5, current 24.7, max 24.8
MCU temperature: min 40.5C, current 44.4C, max 44.5C
Last sensors broadcast 0x00000012 found 2 113 ticks ago, 0 ordering errs, loop time 0
CAN messages queued 627040, send timeouts 0, received 275294, lost 0, errs 0, boc 0, free buffers 18, min 18, error reg 0
dup 0, oos 0/0/0/0, bm 0, wbm 0, rxMotionDelay 0
Accelerometer: LIS3DH, status: 00
I2C bus errors 0, naks 3, contentions 0, other errors 0
=== Filament sensors ===
Interrupt 5726621 to 0us, poll 2 to 1300us
Driver 0: ok