Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. Nengerman
    3. Topics
    • Profile
    • Following 0
    • Followers 0
    • Topics 10
    • Posts 19
    • Best 0
    • Controversial 0
    • Groups 0

    Topics created by Nengerman

    • Nengermanundefined

      Firmware 1.17 naar 1.21RC1 updaten

      Firmware installation
      • • • Nengerman
      2
      0
      Votes
      2
      Posts
      460
      Views

      resamundefined

      https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware

    • Nengermanundefined

      Print quality

      General Discussion
      • • • Nengerman
      6
      0
      Votes
      6
      Posts
      799
      Views

      fmaundefined

      I think you are over-extruding. Try to adjust extrusion ratio down (95%?).

    • Nengermanundefined

      Image

      General Discussion
      • • • Nengerman
      2
      0
      Votes
      2
      Posts
      409
      Views

      DjDemonDundefined

      Post it to postimage.io or similar service.

      Then use

    • Nengermanundefined

      Nema 17 steppenmotor

      General Discussion
      • • • Nengerman
      2
      0
      Votes
      2
      Posts
      693
      Views

      dc42undefined

      I suggest you set the current to 1500mA. If you get skipped steps you can increase it, but above about 2000mA the motors will run hot.

      The default microstepping of x16 with interpolation works well for most motors and printers.

    • Nengermanundefined

      Calibratie

      IR Height Sensor
      • • • Nengerman
      5
      0
      Votes
      5
      Posts
      1.3k
      Views

      Nengermanundefined

      It is a private construction printer with a 300x 300 print bed.
      Thanks for the tip. I will look forward to it soon.

    • Nengermanundefined

      Printhead breaks print

      General Discussion
      • • • Nengerman
      2
      0
      Votes
      2
      Posts
      394
      Views

      dc42undefined

      Some suggestions:

      1. If S3D has an "Avoid crossing perimeters" option for travel moves, enable it.

      2. Use a small amount of Z lift in your retraction settings - although this can be quite slow on non-delta printers.

    • Nengermanundefined

      Bad wifi connection

      General Discussion
      • • • Nengerman
      2
      0
      Votes
      2
      Posts
      373
      Views

      dc42undefined

      It depends on how and where you have mounted the Duet. See https://duet3d.com/wiki/WiFi_disconnections_and_AJAX_timeout_errors.

    • Nengermanundefined

      IR probe install

      Duet Hardware and wiring
      • • • Nengerman
      3
      0
      Votes
      3
      Posts
      590
      Views

      Nengermanundefined

      Thanks for the reply. It works

    • Nengermanundefined

      Extruder dont work

      Tuning and tweaking
      • • • Nengerman
      5
      0
      Votes
      5
      Posts
      830
      Views

      timcurtis67undefined

      Sounds like the wiring to the stepper is wrong. Did you check the poles?

    • Nengermanundefined

      No wifi en errors after update 1.19

      Firmware installation
      • • • Nengerman
      7
      0
      Votes
      7
      Posts
      991
      Views

      Nengermanundefined

      It worked. It works.
      Only confusing that there are several manuals for update firmware on the internet

      Thank you for the assistance.