Topics created by Torro

@tmicke In addition to @Phaedrux 's answer, if you use a mixing hot end, then firmware retraction will retract all filaments whereas slicer retraction will only retract filaments associated with the current tool. This means that filament can be drawn from other inputs rather than the nozzle. So firmware retraction is a must for hot ends which have multiple inputs.

@veti said in Problems with prusaslicer 2.3:

@Torro

just out of curiosity. this is meant in no way as an attack or anything.
if i put in the error message that you typed google gives several threads on this forum with the same solution. adding the T0.
before posting did you even google for the error message?

Fair Question ... but like the OP - I came here first and tried several searches of this forum using its search tool. I had to wade thru 4-5 deep complicated threads before giving it one more search and scroll thru more and more pages of posts not related to my issue before I came across a post with my same error and Prusa Slicer 2.3 - wouldnt have put the issue on Slicer initially - but yet - here it is.

Its a combo of 3.2+ rrf AND PS 2.3 start gcode incompatibilities

How many licks does it take to get to the center of a tootsie pop ? How many searches thru the Duet forum is enough before one posts a new thread ?

Thanks for posting the solution for the rest of us plebs.... gracias.

@torro said in Duet Wifi upload speed question:

@dc42 said in Duet Wifi upload speed question:

M122 P104 S200

SD write speed for 200.0Mbyte file was 1.77MBytes/sec

nearly 2 minutes

That's still a lot better than 400kb/sec. So it's not the SD card that's throttling it, it's the browser+operating system or the network.

got it working. getting connected guide helped.

@phaedrux said in 2 Z motors, to endstops:

@torro said in 2 Z motors, to endstops:

homeall
G91 ; relative positioning
G1 S1 X-300 Y-300 F5000 ; move quickly to X or Y endstop and stop there (first pass)
G1 S1 X-300
G1 S1 Y-300
G1 X10 Y10 F6000 ; go back a few mm
G1 S1 X-20 F360 ; move slowly to X axis endstop once more (second pass)
G1 S1 Y-20 ; then move slowly to Y axis endstop
M98 Phomez.g

Try changing M98 Phomez.g to G28 Z

Same behaviour. I just put the m98 phomez. G in the first line of homeall.g

Now it works as expected

Yes. But i found the failure. All is working fine

this seems more like issue you have to resolve because if your probe is malfunctioning it's better to just ditch it and get something else to probe.

PEI is transparent to near IR light.

@torro said in Wifi Signal strength:

Thanks! A wifi range extender did the Job. Signal strength before - 77, now - 36.

But the fix IP changed... Don't know why, but as long as i know the IP, it's ok...

That will be because the IP address assigned by the router is associated with the MAC address, and it's probably seeing the MAC address of the range extender instead of the MAC address of the Duet.

Ok Thanks again!

great!

Thanks again

That is a brilliant idea. Maybe I will work that out some time when I have more time at hand.

Hi,

You're right. Sorry.

@torro said in getting started, with shut off...:

After the heater tuning, i got a message. Heater overpowered or something similar. Should i decrease the pwm?

That message is very common, especially since E3D started shipping silicone socks with their hot ends. Reducing the PWM won't make it significantly safer.

Done. Works!

Thanks again!

OK, thanks a lot!