Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. luc
    3. Topics
    • Profile
    • Following 0
    • Followers 0
    • Topics 15
    • Posts 106
    • Best 7
    • Controversial 0
    • Groups 0

    Topics created by luc

    • lucundefined

      Very slight systematic waves every about 2mm on the prints

      General Discussion
      • • • luc
      34
      0
      Votes
      34
      Posts
      1.3k
      Views

      lucundefined

      @Phaedrux said in Very slight systematic waves every about 2mm on the prints:

      @luc said in Very slight systematic waves every about 2mm on the prints:

      What object could I print?

      A pyramid/cone.

      Hi, I know it is bad to leave posts like this without feedback but I have a busy and not so busy time at work. Also, I have decided to redo the whole kinematic system in a different way from the current one, and in the spare time, I have started to design and produce the prototype parts of the new system.
      We will catch up later.
      Thank you for now!

    • lucundefined

      Duet 2 wifi AND LIS3DH

      General Discussion
      • • • luc
      33
      0
      Votes
      33
      Posts
      798
      Views

      dc42undefined

      @luc M566 is not relevant here because RRF does not use jerk what starting a move from standstill, or when ending a move at standstill.

    • lucundefined

      Solved Update Duet 2 wifi from 3.1.1 to 3.5.4

      General Discussion
      • • • luc
      17
      1
      Votes
      17
      Posts
      279
      Views

      lucundefined

      @Phaedrux Okay, thank you very much!

    • lucundefined

      RRF 3.1.1 with DWC 3.2?

      General Discussion
      • • • luc
      5
      0
      Votes
      5
      Posts
      281
      Views

      lucundefined

      I had read about some problems on RRF 3.2.2. As soon as I have a moment I update both of them and hopefully well.
      Thanks everyone for the answers.

    • lucundefined

      Guide to configure duex

      Tuning and tweaking
      • • • luc
      4
      0
      Votes
      4
      Posts
      181
      Views

      Vetiundefined

      @luc
      the config tool can generate that for you

    • lucundefined

      Doubt due to passage from 2.05.1 to 3.1.1

      Firmware installation
      • • • luc
      29
      0
      Votes
      29
      Posts
      1.6k
      Views

      lucundefined

      @Phaedrux Ok..... Only during a failure condition....

    • lucundefined

      Duet Web Control

      Tuning and tweaking
      • • • luc
      3
      0
      Votes
      3
      Posts
      179
      Views

      lucundefined

      ok ... done ... thank you very much

    • lucundefined

      Clarification of self-leveling bed

      Tuning and tweaking
      • • • luc
      14
      0
      Votes
      14
      Posts
      603
      Views

      Phaedruxundefined

      I suggest you do a probe repeatability test, it will show you the results of several probing moves in a row and you'll see how there is a bit of variability.

      https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe#Section_Calibrate_the_Z_probe_trigger_height

      Do this procedure but run the G30 S-1 multiple times and check the results. Now you can modify some of the parameters in M558 and redo the test to see how they change the results.

    • lucundefined

      Homing sensorless

      Tuning and tweaking
      • • • luc
      18
      0
      Votes
      18
      Posts
      771
      Views

      Phaedruxundefined

      @luc said in Homing sensorless:

      I will not be able to use the second bump.

      That's right. Because it is too slow. You can still back off from the stalled state position a few mm if you want, but no sense trying to home again more slowly because it won't help accuracy and it likely won't stall the same way.

    • lucundefined

      Extruder engine temperature

      Tuning and tweaking
      • • • luc
      4
      0
      Votes
      4
      Posts
      232
      Views

      Co3getundefined

      @deckingman said in Extruder engine temperature:

      @luc said in Extruder engine temperature:

      SLIM_POWER_LDO-42STH25-1404MAC

      You have nothing to worry about. LDO actually specify a winding temperature, which in the case of that motor is 130 degC. Winding temperatures are generally about 50C more than ambient, so a 130C winding temperature means that you could run that motor inside a heated chamber temperature of 80C. For info, LDO also make a high temperature version which has a winding temperature rating of 180 deg C meaning that it could be used in a heated chamber at up to 130 deg C.

      @deckingman
      I have this same motor and googled my way in here looking up the temperature rating. I can't find it on LDO's website. where did you pick up the into that the motor is OK to 130c?

      I run a 50c chamber.

    • lucundefined

      Set e-step bmg

      Tuning and tweaking
      • • • luc
      5
      0
      Votes
      5
      Posts
      6.4k
      Views

      droftartsundefined

      @luc see the guide here: https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+4:+Calibration/40#s165

      Ian

    • lucundefined

      Update firmware

      Firmware installation
      • • • luc
      3
      0
      Votes
      3
      Posts
      175
      Views

      lucundefined

      All okay, many thanks

    • lucundefined

      Doubts about correct compensation mesh configuration

      General Discussion
      • • • luc
      5
      0
      Votes
      5
      Posts
      254
      Views

      lucundefined

      @Veti said in Doubts about correct compensation mesh configuration:

      @luc said in Doubts about correct compensation mesh configuration:

      G31 P25 X-26 Y0

      is the bltouch to the left of the hotend? sometimes this can be set wrong.

      Yes, bltouch is on the left. It is a support that I personally designed.

      M557 X25:260 Y25:260 S78 ; Define mesh grid

      your grid is very largely spaced. try S20

      I try! I had given more space to have 16 points ... with S20 it will do many more.

      Thank you very much!

    • lucundefined

      Retraction firmware

      General Discussion
      • • • luc
      4
      0
      Votes
      4
      Posts
      491
      Views

      deckingmanundefined

      @luc Yes that would give you 1.5 mm retraction at 40mm/sec. And yes, you can put the command anywhere in your configuration file.

    • lucundefined

      Comand pause e resume from DWC

      Duet Hardware and wiring
      • • • luc
      9
      0
      Votes
      9
      Posts
      519
      Views

      Phaedruxundefined

      Printing from the SD card is definitely the preferred way to do it with the duet. More reliable and opens some more possibilities.

      Most slicers now let you upload directly to the duet and start the print with a single click.