video_2021-02-11_00-13-44(1).mp4
We are doing some prototyping, with a regular orbiter, changing some aspects of the body.
It actually is a pivot extruder, so it can rotare freely within the rod arms...
It´s not my doing, just a friend´s I am helping him to achive it
@arhi I meant the the first prototype had wifi disconections due to long tracks, this one has shorter pads, and looks like it works just fine while printing. The first one just didn´t work while printing
@Fred-Y I use a ptfe foil to lubricate ball-arm joints.
Here a bunch of spanish guys are using this ptfe tape on our hayden´s arms.
Succesfully updated to 2.13 and solder pad restored
thanks
Recap: Old smarteffector v2 that does not remember sensitivity custom settings.
Solution: Flash new firmware V2.13 via PROG pin pads on top board side.
Procedure: Solver pin strip to exposed pads and use a direct pin to pin cable from the ISP port on programer
Programed with a FT232r programer with AVRDUDES app
@Branzo said in Thermistor Semitec 104nt config problem:
M308 S0 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8
M950 H0 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H0 S500 ; set temperature limit for heater 0 to 500C
if you declared S0 and H0 has the heated bed, need to declare S1 and H1 as the heater
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.060000e-8 A"Nozzle E0" R4700 ; E3d configure sensor 0 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 2
M143 H1 S285 A2 ; disable temporarily H1 if temp exceeds 285C
M143 H1 S295 A0 ; heater fault H1 if temp exceeds 295C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M570 H1 P10 T30 ; heater fault for 10 seg of 30ºC excursion
@oliof when you flash klipper fw it doesn´t finish quite well, and board does not respond.
Just reflash RRF again and it works fine.
That´s a semibrick...board not working but you are able to recover it by regular procedure.
@apak 
seems everything is in place, also the 74HC74
guess that the chinnese clons just install everything for the wifi version and then just plug the ethernet board
just saw new source for smarteffector v4 on github, what would be new on it, is it there any specs or pictures?
@tekkydave no it´s not, that´s the case for the monitor, I am looking for the part to attach it to the titan idler, thanks anyway
@arhi
I had to make my own pin strip since on my local store didn´t have them
It´s working fine, no disconnections while printing like with the first prototype
I have a macro to preheat bed and nozzle to a desire temp.
With previous fw, I just run it, and the screen info updated while heating.
https://vimeo.com/471673926
but with paneldue 3.2, it just does not update screen info until macro is finished.
https://vimeo.com/471673915
FW 3.2Beta2
DWC 3.2Beta2
Wifiserver 1.24b
paneldue 3.2
macro
M104 S150 ; set extruder temp
M140 S60 ; set bed temp
M190 S60 ; wait for bed temp
M109 S150 ; wait for extruder temp
@barracuda72 there is no resistor, only the cables solderded.
Just cutted wired and it worked, thanks
@jackantubis nice, thanks for sharing, I am rebuilding a Tevo Little monster for a total of 1000mm Z size, so I love the wireless solution for the paneldue
I had fw 3.4.5 with 9 flashes
I updated to 3.5.0 beta3 and it flashes 2 times
So I guess it was a bug
@gloomyandy
@jay_s_uk
got it working,
now I need to now what should I do with it.
It´s a delta printer
