Posts made by weed2all

@edsped you only need to use the 2 pins without * markings...those that are market with * are passed directly from IN and OUT CAN ports!

@edsped 2 fires is for data and other 2 wires is for power!

@samlogan87 I'm using my esun ebox lite to maintaining my filament dry while I'm printing!

@tecno your orbiter mounting is not good...I already told you on the other thread you asked...the orbiter mounting can't be in contact with the strain gauge of the smart effector because will not work properly, it only need to be connected with the 3 point mount holes and not the entire surface!

@tecno said in Software bundle 3.5.0-beta.3 now available:

@dc42

It is 3.0
Not same sensitivity on print area that is approx 450mm in diameter = No reliable mesh.

Also I suspect the mounting of the extruder /adapter may cause issues as well.

i remember when i designed the mount for lgx lite for my smart effector the first 3 iterrations of the mount was just like that and never had a good probe because the mount interfere with the strain gauge of the effector...and then i decided to raise it a bit and that sorted out...this is how it looks righ now

i added some spacers to the mount to raise it from the smart effector then i integrate them on the final deign

@IndeX4D magnum + will came in handy if you still have!thank you!

@dc42 tell us more please!

@MaukaEast what mount do you use? Can you show a photo? The mount you have is made by you or is what precision piezo send with the orion?

@MaukaEast the precision piezo orion v2 I have has a small potentiometer on it to adjust the sensitivity...have you tried adjusting it..
Adjust it and tap on the nozzle and see the impact it does...

@MaukaEast change the R value from 0.3 to 0.5...

@printnoob of course...

@printnoob well...you don't need klipper...reprap firmware is more than capable and the best thing is you don't need a raspberry pi to have a great web interface and easy to config you printer!go ahead and start looking at
https://docs.duet3d.com/en/How_to_guides/Getting_connected/Getting_connected_to_your_Duet

@jay_s_uk please post here the link for the boards when they're be available for purchase

@JADoglio voron printers don't they are setup to home in the max x and y like right side and back instead of the normal front left as what everything else?I don't own a voron but from all the videos I seen on YouTube they certainly home at max position!

@dc42 thanks for reply...I think I'll sell my duet 3 unused board and buy the new version!

@jay_s_uk is what I was thinking as well...seeing now the pdf of both version of the boards...

@droftarts thanks for fast response, though I saw the documentation before, my questions still remain what componentes changed from v1.01 to v1.02 to make it work with 48v beside the large capacitors that everyone could see...
In other words if I change the small capacitors from V1.01 with the larger ones that are present on V1.02 can i use 48v for input voltage or I need to change some other components...

Hello...as the title implies I would want to know what the difference for board 6HC 1.01 and 1.02 are in terms of components used to make the latest to run at 48v?
I have a V1.01 board that bought it for a cnc application and due to only accept 32v as input voltage I changed it for something else to run my cnc, but now as the new revision board accept the 48v I want if possible to gather all the components to make my 6HC V1.01 to run at 48v as well...beside large capacitors I see on the new revision board what else need to be changed to make it work!

@SANJR C is common so it need to connect to Gnd, and NC pin to iox.in pin on duet board...the NO wire is left alone without connection

@davidewen no worries...just rememberd I saw it!