Let us know what you find out.

@3dpandme when i enter that IP address in my browser it connects fine so I'm a bit confused by the network error.

@phaedrux I am able to ping the board and send commands using the micro USB and I have managed to get the full system working by bridging my wifi and ethernet together and using the autogenerated ip from that. When I go back in tomorrow I will try setting the subnet manually and see if that works

@ravs99 You'll see them in the status page when running a print - bottom left corner

Sliders1.PNG

Sliders2.PNG

For anyone later reading this thread having similar issue:

My SD card is Class 10 (rated at 10 Mb/s write) Running M122 P104 reports 10 Mb/s write 0.8 Mb/s read on my machine.

Writing to internal SD card on 6HC main board via DWC yields transfer rates of ~1Mb/s while writing to same SD card inserted into PanelDue slot has ~180 Kb/s transfer rates. Moral of the story is: use the external socket on the PanelDue as an external/removable socket not for DWC transfers. Profound, I know 🙂

@droftarts thank you ! will give this a go

@phaedrux It is correctly processed by DSF 3.4.1, I just checked (object height = 11.05mm). The number of layers was not present in the original file but once added that is parsed correctly, too.

@jay_s_uk Well it seems to break when I update anyway, so next time I do, I'll try it out.

I see you're using the 3.4.2 RC3 which includes an updated wifi server 1.27 beta.

Can you try flashing back to 3.4.1 using the full zip file to compare performance with the previous wifi server 1.26?

Really loving the new self service feature of the forum.

The Duet Wifi board has been replaced with an Ethernet board, and the machine is now on a separate network that will not be accessible from the public wifi or publicly accessible computers.

Thanks.

@jay_s_uk Okay I will look into this. Thank!

Weirdest thing... It's back up now.

WiFi module has been up the whole time (it was responding to pings(ICMP))
Telnet to ports 23 and 80 were getting nothing

I did not connect directly to USB with my workstation and try to print.
I did put a file in the gcode directory on the SD card by hand and was able to print.

I did set up and connect an OctoPi as a possible work around and it did seem to be communicating but I had not had a chance to print with it.

I've been beating my head against my desk for the last 8 hours trying to get this sorted
and I walk away from my desk for few minutes and its back up.

I do not like issues that seem to resolve themselves in this way for obvious reasons.

It may have something to do with burning some sage and swinging a dead chicken around but.... That's dinner so it would have happened regardless.

Just for posterity:

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.1 (2022-06-01 21:05:28) running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DJM-9178L-L2MS8-6JKDA-3S06M-K8HAP
Used output buffers: 3 of 26 (26 max)
=== RTOS ===
Static ram: 23860
Dynamic ram: 76456 of which 12 recycled
Never used RAM 8248, free system stack 96 words
Tasks: NETWORK(ready,37.5%,242) HEAT(notifyWait,0.1%,324) Move(notifyWait,2.9%,292) DUEX(notifyWait,0.0%,24) MAIN(running,59.4%,460) IDLE(ready,0.1%,30), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 01:52:37 ago, cause: power up
Last software reset at 2022-08-15 23:22, reason: User, GCodes spinning, available RAM 8608, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x0c
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 15.3, current 23.6, max 28.3
Supply voltage: min 23.9, current 24.1, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/40/40, gc cycles 0
Events: 1 queued, 1 completed
Driver 0: standstill, SG min 0
Driver 1: standstill, SG min 0
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min 0
Driver 4: standstill, SG min n/a
Driver 5: standstill, SG min 0
Driver 6: standstill, SG min 0
Driver 7: standstill, SG min 0
Driver 8: standstill, SG min n/a
Driver 9: standstill, SG min n/a
Driver 10:
Driver 11:
Date/time: 2022-08-29 15:49:42
Cache data hit count 4294967295
Slowest loop: 135.33ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.9ms, write time 14.1ms, max retries 0
=== Move ===
DMs created 83, segments created 27, maxWait 3482734ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 40317, completed 40317, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.5
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Filament sensors ===
Extruder 0: pos 247.50, errs: frame 0 parity 0 ovrun 0 pol 0 ovdue 0
=== DueX ===
Read count 1, 0.01 reads/min
=== Network ===
Slowest loop: 40.98ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.26
WiFi MAC address 84:0d:8e:ad:74:86
WiFi Vcc 3.40, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 24680
WiFi IP address 192.168.1.226
WiFi signal strength -37dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 4 0 0 0 0 0 0 0

M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is enabled on port 23
Error: Heater 1 not switched on due to bad model

config.g

@jay_s_uk You and I said the same thing, about the negative temperature coefficient. I said resistance is higher at lower temperatures; you corrected to lower at higher temperatures. 🙂

However, your statement about the value for a thermistor being specified at zero degrees is wrong. Most thermistors are standardized at 25C. Pt100/Pt1000 are, indeed, standardized at 0C. But it is still correct that the 100000 is the right number to have put in the file.

@chrishamm Thanks for letting me know --- that it's not just some faulty memory of mine.

@quentin said in Issue with response of the console:

firmware version 3.2.2

Might be a good idea to update the firmware and DWC to 3.4.1 Or 3.4.2 which is coming soon.

@kgolger what are in your driver stall files?

@rushmere3d
At this moment I have problem with printing. Filament move after extruder and after few sec is a one big ball

@jay_s_uk

So it was so now I am back to start printing again. Thanks very much appreciated!

@thalaniel This is related to the same problem as in your other thread. Make sure the microSD card is properly inserted.