Topics created by RodrigoRMaraujo

@droftarts Hi, I tested and it is working fine, also changed to 5x5 points.

@gloomyandy and @jay_s_uk
First of all, thanks for answering.

I don't have enough knowledge to start a challenge like this, I have no idea how it would be done lol.
Using canbus would be ideal, because I'm currently converting a machine running klipper, which has an ebb42 board in the car.
Because of the difficulty, I think I'll opt to run all the wiring for the car's accessories (without canbus).

I'm leaving klipper and converting my printers back to RRF because of the complexity of klipper (for me). I want to go back to the simplicity of RRF and not depend on an SBC running linux.

Sorry for the bad English, translated by google.

@jay_s_uk
Thank you!

@droftarts thanks for replying.
This model you mentioned, from aliexpress, theoretically doesn't need any changes to the wiring, right?

@RodrigoRMaraujo said in Duet maestro - Diag led does not turn off:

I've been buying Duets on AliExpress since 2019

Just curious, since you’ve benefited so much from their work without buying genuine hardware, have you offered to contribute to the Duet development team?

@RodrigoRMaraujo Thanks for reporting this, it will be fixed in the next 3.5 release. Version 3.6 is not affected.

@droftarts thank you!
While you were writing, I was researching this very documentation.
Thank you very much.

I don't know yet how to mark a topic as resolved. Should I wait for the administration or can I do it myself?

@droftarts and @jay_s_uk
Thanks for the answers!
The sum of the 2 suggestions solved my problem.
I think the translation of the documentation into Portuguese by Google made me misspell the D parameter of the M563 command.
I had really forgotten to activate T0.
I used RRF for a few years, since v2.03 and migrated in 2022 to klipper on all machines. Now I'm going back to RRF and I'm trying to remember everything.
Thanks to both of you!

@dc42 thanks for replying!
I really wasn't thinking about fixing the board, there's no one in my area who can do that.
I've already ordered a new board to replace the one I burned. Since it's a very basic printer, I believe the RRF 3.5 will be perfect for me.
For the other printers, I have the Duet 2 WiFi and "Fysect Big Dipper" boards, and with these I'll be able to keep up with the new versions of the RRF.
I'm going to keep the Maestro that I burned as a souvenir so I don't do this kind of stupid thing again, lol.
Thanks!

Hi @jumpedwithbothfeet , thanks for replying.

It's just that the M308 command is not enough for it to appear on the main tab. I already have the sensor set up and working.
For it to appear on the main tab, it must be connected to a heater, just like the hotend and table sensors.

tools.png

See the "Sensor borda" in the second tab (extras). I would like this to appear in the tools tab.
Extras.png

As I understand it, I need to create a virtual heater and connect this sensor to this heater, so that it appears in the tools tab.

@droftarts An excellent contribution, thank you very much for this!

You can get devices like this that provide 5v via usb in a convenient package.

https://www.amazon.ca/Charger-ADSDIA-Aluminum-Waterproof-Motorcycle/dp/B07PN5YZX3/ref=sr_1_5?crid=8GK4ZUT768DM&dchild=1&keywords=usb+boat+charger&qid=1631389908&sprefix=usb+boat%2Caps%2C333&sr=8-5

@alex-cr I made some modifications for myself but your script served as the basis. It worked great, thanks!

;Bed edge sensor M308 S0 P"e1temp" Y"thermistor" T100000 B3950 C0.0 A"Sensor borda" ; configure sensor 0 as thermistor on pin temp0 ;Sensor on silicone pad M308 S2 P"bed_temp" Y"thermistor" T100000 B3950 C0.0 A"Sensor PAD" ; configure sensor 0 as thermistor on pin temp1 M950 H0 C"bed_heat" T0 Q60 ; create bed heater output on out0 and map it to sensor 0 M307 H0 B0 S0.6 ; disable bang-bang mode for the bed heater and set PWM limit M140 P0 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for build plate to 120C M143 H0 T2 P1 S120 A2 ; Monitor heater thermistor, if temp goes above 125C temporarily turn off M143 H0 T2 P2 S126 A3 ; Monitor heater thermistor, if temp goes above 126C cut "atx" supply M307 H0 B0 R0.144 C1979.0 D43.36 S0.60 V24.0 ; pid test 09/09/2021

@fcwilt yes, thank you!

@dc42 thank you!

@o_lampe Thanks for answering. I can't use the expansion connector because I have a duex5 attached. I also don't have the knowledge to understand which pins can be used. I am learning...

@rodrigormaraujo yes, use daemon.g
some like

if heat.heaters[1].current > 45 M150...

@dc42 said in Help with sensorless in duet 3 mini 5+:

thanks for reporting back! I'm glad you got it working.

It was amazing, thanks again!

This method is pretty cool @mrehorstdmd. I also used it like that for a long time, but I'm building a voron and I wanted to leave a small camera inside the machine, more for aesthetic reasons. I used a cell phone for a long time and then switched to a xiaomi ip camera, to look at 2 printers when I was away from home. Thanks for your response!

Does it seem like it's correcting in the wrong direction?

You may be running afoul of this guidance:

You must use the M671 command to define the X and Y coordinates of the leadscrews. The M671 command must come after the M584 command and must specify the same number of X and Y coordinates as the number of motors assigned to the Z axis in the M584 command; and these coordinates must be in the same order as the driver numbers of the associated motors in the M584 command. The M671 command must also come after any M667 or M669 command.

https://duet3d.dozuki.com/Wiki/Bed_levelling_using_multiple_independent_Z_motors

Post your config.g please.