@Phaedrux will do! But… I can say it does remain because my E-stop isn’t hooked up to the duet but to the mains. In an emergency I want everything to stop. Full power cycle is on my list of standard troubleshooting approaches.

I haven’t had any issues since my last post and the only thing that’s changed is that I’ve commented out the line declaring DWC needs a password.

@chrishamm it works well on my machines, thank you again for your time on my issue

@droftarts thanks a lot. I know the Zip download. Cool would be one button. I will look in the other options.

By the way, after changing the SD card to a new one, I did not face the issue anymore.

Thanks.

@tkln no, you need to define each motor as a separate axis, and move that. So for the X axis, define an extra axis U which has the motor you want to move independently:

M584 X0.2:0.3 U0.3

Then you can move the U axis with G1 U5 (relative rather than anbsolute axis movements will probably work best). I’m not sure exactly what will happen when you send a subsequent G1 X… movement, though. It should keep the spacing you have set. You will also need to home the U axis first, or give it a position with G92.

RRF does not natively support a six axis delta, so it will rely on the slicer to send appropriate commands if using more than the standard 3 axes.

Ian

Hi guys, did you ever resolve this? I'm going through a similar issue. Thinking of running 24V to my 6HC and 48V to the expansion board (3HC). Will this work? New topic posted here:

https://forum.duet3d.com/topic/36953/duet6hc-24v-and-48v-psu-s-for-different-components/8?_=1731730867239

Thanks 🙂

@dhmclean Yes, I have two older Asus routers that run 24/7 for months whereas my latest 3 (two mesh and one standard set into the mesh) flake over time fairly consistently. Admittedly the older firmware was comparatively basic.

I assume you are connected by USB and using a terminal software to send commands.

What terminal software are you using?

Can you send M122 and copy paste the results here?

@megamachine said in cannot connect to web control:

"could not establish a connection to the duet firmware! Please check your settings and try again"

Where exactly are you seeing this message?

It works 😉

@schild0r said in Connect Ubuntu PC Directly to DUET EtherNet Without a Router?:

I ended up with a different tutorial

I'm always amazed by the number of alternative packages to do "the same thing" along with instructions that sometimes work and sometimes don't. That tutorial takes a slightly different approach but better still WORKED FIRST TIME !!

Congrats and thanks for posting the link.

How do you have your heaters and thermistors connected?

@ram yes you can push files to the Duet but it can't go out and "pull" them (at least with Duet 2). Duet 3 OTOH will allow for a plugin to be written on the SBC that does that.

@maerkler said in Duet 2 Wifi connection Problems:

; Bed probe section (not needed if you use a bed.g file)
;*** Adjust the XY coordinates in the following M557 commands to suit your build and the position of your Z probe
M557 P0 X60 Y0 ; Four...
M557 P1 X60 Y165 ; ...probe points...
M557 P2 X200 Y165 ; ...for bed...
M557 P3 X200 Y0 ; ...levelling
;M557 P4 X141 Y82.5 ; 5th probe point for levelling (un-comment this to get a 5th point at the centre of the bed)

You're not using M557 correctly at all. See here:

https://duet3d.dozuki.com/Wiki/Gcode#Section_M557_Set_Z_probe_point_or_define_probing_grid

https://duet3d.dozuki.com/Wiki/Using_mesh_bed_compensation

Parameters to define G32 probe points (Cartesian/CoreXY printers only, deprecated and not supported in firmware 1.18 and later)

Pnnn Probe point number
Xnnn X coordinate
Ynnn Y coordinate
Example

M557 P1 X30 Y40.5

Can you confirm that you are still running main firmware 2.02, as shown in the M122 listing in your first post?

I can ask chrishamm to look into this message, but he will probably ask you to upgrade to Duet Web Control 2.0.0-RC6, available at https://github.com/chrishamm/DuetWebControl/releases.

@tracar said in Duet wifi lost web connection:

same problem here exactly as above.., web interface hangs,

This thread is very old and discusses very old firmware. I suggest you start a new thread with your issue. Are you running up to date firmware?