@sebkritikel Awesome news! Thank you.

@dc42

Good to know! Thanks a bunch.

@dc42 said in Duet 2 wifi - Reprap 3 MPU fan thermal control:

I have my electronics cooling fan set up to monitor both the driver and MCU temperatures, with a temperature range of 45:55. That way, the fan will start to spin if the MCU temperature exceeds 45C, and it will be full on if either MCU temperature exceeds 55C or there is a driver overheat warning.

@dc42 can you please share the code. Thanks a lot.

@Nxt-1 Im an old kisslicer user and always have been wondering why there is no firmware retraction... But you post is like "UAUUUU" jajajaj
You mean that setting "Mark Path Start/Stop" with the G10/1 option that activates firmware retracion? Of course also I need to configure it on the config.g for example.

I would add or ask: you would need to set the destring value to CERO also on the material tab on kisslicer right?

@flyscha said in Duet 3 6HC + Scanning Z Probe, not connecting:

Sorry, I meant to say "I'm NOW getting a connection..."

I've edited your post for clarity.

Ian

@Phaedrux Pump need 0.9 amps, 24V, my PSU can supply 30 amps at 24V. So I have enough power. It is a water pump.

I have just finished "solving" the problem. I just re flashed the sd card and everything is working as expected, no config change, no witing change, just burnt a brand new sd card image

@lazy_mosquito thanks, I think it would help if we changed all Duet 3 CAN-FD expansion board documentation to state that they are compatible with all Duet 3 mainboards. leaving this here if anyone else searches the forums for this question.

Looks like i am not getting a lot of response.
Questions not clear or nobody used integrated servo motors before with 6xd?

@droftarts said in Problem with heaters:

M563 P0 H0 D0 F0

Yeah that solved it! Thank you very much!!!👍 👍 👍 👍

@Phaedrux the mlx90640 uses the pins from RPi
SCA,SCL,GND And VCC,
And I just need any two out put for controlling leds,
Is this possible

@droftarts said in 1LC TOOLBOARD v1.1. Accelerometer fail:

1N4148W

Thanks for the information, I will buy the diode and solder it, I hope this will solve the problem.

@curieos said in 6XD 5V Input Voltage Limits:

If the 5V supply in question were adjustable, and the 6XD were to allow some fraction of a volt over 5V, would it be possible to overcome the voltage drop from the protection circuitry?

Yes. The protection circuitry comprises a Schottky diode between 5V_EXT_IN and the 5V_EXT supply that you can pass to the Pi. This will drop around 0.4V. So you will need to provide about 5.6V from your PSU. Take care not to exceed 5.7V.

@droftarts lol, thank you very much

@droftarts we figured it out. The bltouch had a small metal shaving in the pins from factory. Then the fans the config.g somehow didn't get copied over. So I got a little ahead of myself with this post.

@droftarts , yes just was reading that as you posted it . got it. done. No more timeout errors but still having issue with sending M950 Jx tests (J1 to J6 )

@droftarts
Thank you so much.

@timoschuett the BTT EXP MOT may work

@droftarts I solved the problem and it worked! I have attached the schematic as a picture:

duet_3_mini_5+_wiring_latest.png

@TypQxQ if the 3.3V regulator is getting hot then most likely another component has failed. Is anything else getting hot? Check the SD card the WiFi module and the microcontroller in particular.